300-710 Exam Dumps (V25.02) Are the Smarter Choice for Passing: Continue to Read 300-710 Free Dumps (Part 3, Q81-Q110)

1. In a Cisco AMP for Networks deployment, which disposition is returned if the cloud cannot be reached?

2. Which two remediation options are available when Cisco FMC is integrated with Cisco ISE? (Choose two.)

3. Which connector is used to integrate Cisco ISE with Cisco FMC for Rapid Threat Containment?

4. What is the maximum SHA level of filtering that Threat Intelligence Director supports?

5. Refer to the exhibit.

And engineer is analyzing the Attacks Risk Report and finds that there are over 300 instances of new operating systems being seen on the network.

How is the Firepower configuration updated to protect these new operating systems?

6. An engineer is implementing Cisco FTD in the network and is determining which Firepower mode to use. The organization needs to have multiple virtual Firepower devices working separately inside of the FTD appliance to provide traffic segmentation.

Which deployment mode should be configured in the Cisco Firepower Management Console to support these requirements?

7. A network engineer is extending a user segment through an FTD device for traffic inspection without creating another IP subnet.

How is this accomplished on an FTD device in routed mode?

8. An engineer is configuring a second Cisco FMC as a standby device but is unable to register with the active unit.

What is causing this issue?

9. After using Firepower for some time and learning about how it interacts with the network, an administrator is trying to correlate malicious activity with a user.

Which widget should be configured to provide this visibility on the Cisco Firepower dashboards?

10. An engineer has been asked to show application usages automatically on a monthly basis and send the information to management.

What mechanism should be used to accomplish this task?

11. An engineer is setting up a new Firepower deployment and is looking at the default FMC policies to start the implementation During the initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass.

Which default policy should be used?

12. An engineer currently has a Cisco FTD device registered to the Cisco FMC and is assigned the address of 10 10.50.12. The organization is upgrading the addressing schemes and there is a requirement to convert the addresses to a format that provides an adequate amount of addresses on the network.

What should the engineer do to ensure that the new addressing takes effect and can be used for the Cisco FTD to Cisco FMC connection?

13. A security engineer is configuring an Access Control Policy for multiple branch locations These locations share a common rule set and utilize a network object called INSIDE_NET which contains the locally significant internal network subnets at each location.

What technique will retain the policy consistency at each location but allow only the locally significant network subnet within the applicable rules?

14. An engineer is troubleshooting application failures through a FTD deployment. While using the FMC CLI. it has been determined that the traffic in question is not matching the desired policy.

What should be done to correct this?

15. An administrator is attempting to remotely log into a switch in the data centre using SSH and is unable to connect.

How does the administrator confirm that traffic is reaching the firewall?

16. What is the advantage of having Cisco Firepower devices send events to Cisco Threat response via the security services exchange portal directly as opposed to using syslog?

17. An organization has noticed that malware was downloaded from a website that does not currently have a known bad reputation.

How will this issue be addresses globally in the quickest way possible and with the least amount of impact?

18. An administrator is working on a migration from Cisco ASA to the Cisco FTD appliance and needs to test the rules without disrupting the traffic.

Which policy type should be used to configure the ASA rules during this phase of the migration?

19. Which two routing options are valid with Cisco FTD? (Choose Two)

20. With Cisco FTD integrated routing and bridging, which interface does the bridge group use to communicate with a routed interface?

21. While configuring FTD, a network engineer wants to ensure that traffic passing through the appliance does not require routing or Vlan rewriting.

Which interface mode should the engineer implement to accomplish this task?

22. The event dashboard within the Cisco FMC has been inundated with low priority intrusion drop events, which are overshadowing high priority events. An engineer has been tasked with reviewing the policies and reducing the low priority events.

Which action should be configured to accomplish this task?

23. An engineer is configuring a cisco FTD appliance in IPS-only mode and needs to utilize fail-to-wire interfaces.

Which interface mode should be used to meet these requirements?

24. Which two considerations must be made when deleting and re-adding devices while managing them via Cisco FMC (Choose two).

25. Refer to the exhibit.

An administrator is looking at some of the reporting capabilities for Cisco Firepower and noticed this section of the Network Risk report showing a lot of SSL activity that cloud be used for evasion.

Which action will mitigate this risk?

26. An engineer is attempting to add a new FTD device to their FMC behind a NAT device with a NAT ID of ACME001 and a password of Cisco388267669.

Which command set must be used in order to accomplish this?

27. A user within an organization opened a malicious file on a workstation which in turn caused a ransomware attack on the network.

What should be configured within the Cisco FMC to ensure the file is tested for viruses on a sandbox system?

28. Refer to the exhibit.

What must be done to fix access to this website while preventing the same communication to all other websites?

29. A network administrator is seeing an unknown verdict for a file detected by Cisco FTD.

Which malware policy configuration option must be selected in order to further analyse the file in the Talos cloud?

30. administrator is configuring SNORT inspection policies and is seeing failed deployment messages in Cisco FMC.

What information should the administrator generate for Cisco TAC to help troubleshoot?