300-710 Exam Dumps (V25.02) with 381 Questions and Answers: You Can Check the 300-710 Free Dumps (Part 1, Q1-Q40) to Verify the Quality

1. What is a result of enabling Cisco FTD clustering?

2. Which two conditions are necessary for high availability to function between two Cisco FTD devices? (Choose two.)

3. On the advanced tab under inline set properties, which allows interfaces to emulate a passive interface?

4. What are the minimum requirements to deploy a managed device inline?

5. What is the difference between inline and inline tap on Cisco Firepower?

6. With Cisco Firepower Threat Defense software, which interface mode must be configured to passively receive traffic that passes through the appliance?

7. Which two deployment types support high availability? (Choose two.)

8. Which protocol establishes network redundancy in a switched Firepower device deployment?

9. Which interface type allows packets to be dropped?

10. Which Cisco Firepower Threat Defense, which two interface settings are required when configuring a routed interface? (Choose two.)

11. Which two dynamic routing protocols are supported in Firepower Threat Defense without using FlexConfig? (Choose two.)

12. Which policy rule is included in the deployment of a local DMZ during the initial deployment of a Cisco NGFW through the Cisco FMC GUI?

13. What are two application layer preprocessors? (Choose two.)

14. An engineer is tasked with deploying an internal perimeter firewall that will support multiple DMZs

Each DMZ has a unique private IP subnet range.

How is this requirement satisfied?

15. An engineer must configure high availability for the Cisco Firepower devices. The current network topology does not allow for two devices to pass traffic concurrently.

How must the devices be implemented in this environment?

16. When deploying a Cisco ASA Firepower module, an organization wants to evaluate the contents of the traffic without affecting the network. It is currently configured to have more than one instance of the same device on the physical appliance.

Which deployment mode meets the needs of the organization?

17. An organization has a Cisco FTD that uses bridge groups to pass traffic from the inside interfaces to the outside interfaces. They are unable to gather information about neighbouring Cisco devices or use multicast in their environment.

What must be done to resolve this issue?

18. A network engineer implements a new Cisco Firepower device on the network to take advantage of its intrusion detection functionality. There is a requirement to analyze the traffic going across the device, alert on any malicious traffic, and appear as a bump in the wire.

How should this be implemented?

19. Which two conditions must be met to enable high availability between two Cisco FTD devices? (Choose two.)

20. An engineer is building a new access control policy using Cisco FMC. The policy must inspect a unique IPS policy as well as log rule matching.

Which action must be taken to meet these requirements?

21. Within an organization's high availability environment where both firewalls are passing traffic, traffic must be segmented based on which department it is destined for. Each department is situated on a different LAN.

What must be configured to meet these requirements?

22. An engineer is configuring a Cisco IPS to protect the network and wants to test a policy before deploying it. A copy of each incoming packet needs to be monitored while traffic flow remains constant.

Which IPS mode should be implemented to meet these requirements?

23. A network security engineer must replace a faulty Cisco FTD device in a high availability pair.

Which action must be taken while replacing the faulty unit?

24. An administrator is optimizing the Cisco FTD rules to improve network performance, and wants to bypass inspection for certain traffic types to reduce the load on the Cisco FTD.

Which policy must be configured to accomplish this goal?

25. A Cisco FTD has two physical interfaces assigned to a BVI. Each interface is connected to a different VLAN on the same switch.

Which firewall mode is the Cisco FTD set up to support?

26. An organization is migrating their Cisco ASA devices running in multicontext mode to Cisco FTD devices.

Which action must be taken to ensure that each context on the Cisco ASA is logically separated in the Cisco FTD devices?

27. Which firewall design allows a firewall to forward traffic at layer 2 and layer 3 for the same subnet?

28. Which two OSPF routing features are configured in Cisco FMC and propagated to Cisco FTD? (Choose two.)

29. When creating a report template, how can the results be limited to show only the activity of a specific subnet?

30. What is the disadvantage of setting up a site-to-site VPN in a clustered-units environment?

31. Which two statements about bridge-group interfaces in Cisco FTD are true? (Choose two.)

32. Which command is run on an FTD unit to associate the unit to an FMC manager that is at IP address 10.0.0.10, and that has the registration key Cisco123?

33. Which two actions can be used in an access control policy rule? (Choose two.)

34. Which two routing options are valid with Cisco Firepower Threat Defense? (Choose two.)

35. Which object type supports object overrides?

36. Which Cisco Firepower rule action displays an HTTP warning page?

37. What is the result of specifying of QoS rule that has a rate limit that is greater than the maximum throughput of an interface?

38. Which Firepower feature allows users to configure bridges in routed mode and enables devices to perform Layer 2 switching between interfaces?

39. In which two places can thresholding settings be configured? (Choose two.)

40. In which two ways do access control policies operate on a Cisco Firepower system? (Choose two.)