NS0-164 Free Dumps (Part 2, Q41-Q80) Are Also Online: Helping You Check the Quality of the NS0-164 Dumps (V8.02)

1. An administrator has an existing FlexVol accessed by Linux hosts over NFSv3. A CIFS share to the same FlexVol was created for SMB access. Windows users are unable to view the share. CIFS share permissions allow for read and write access for the Windows users.

What does the administrator need to modify to allow SMB access?

2. The snapvault update command is only available on the secondary system.

3. What is the maximum number of disk shelves per loop in a fabric-attached MetroCluster?

4. Which ONTAP feature discards identical blocks and replaces them with references to a single shared block?

5. Which one of the following statements apply to Advanced Single Instance Storage (ASIS)?

6. 1.Data ONTAP uses inodes in an active file system to reference__________________.

7. Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?

8. Which two options must be configured to use tamperproof snapshots? (Choose two.)

9. What does it signify if the disks are "not owned" in a FAS270C appliance?

10. Which one of the following statements apply to the Free Space Estimator utility?

11. When creating an S3 bucket using System Manager, ONTAP uses which default performance service level for an AFF?

12. The NearStore system is not the recommended secondary storage appliance for Open System SnapVault.

13. Which one of the following commands would you use to disable client access to snapshots on a volume called /vol/flexvoM?

14. Which three are true when creating a SyncMirror volume? (Choose 3)

15. What command would you enter to restore the /vol/flexvol0/etc/rc file from a snapshot to the /vol/flexvol0/home directory?

16. Which statement describes the results of the snapmirror resync command?

17. Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner node, Node 2, can see all of Node 1s disk shelves.

Which one of the following features will cause Node 2 to monitor this error condition for a period of three minutes (by default), and then forcibly take over Node 1 if the error condition persists?

18. You have determined that the failure to a MetroChister is a disaster.

Which step should you take?

19. Which OSSV package would you use to perform an OSSV unattended installation?

20. Which two supported methods would you use to restore data from a SnapVault for NetBackup Volume?

21. Which command allows you to access the other nodes console after a takeover has occurred?

22. Which ONTAP feature will allow WORM and non-WORM volumes in the same aggregate?

23. The SnapVault secondary system allows you to keep a separate schedule of Snapshot copies from your primary system.

24. You can unlicense the cluster feature only in

25. What two actions occur automatically if the system detects ransomware activity when Autonomous Ransomware Protection is enabled? (Choose two.)

26. Which NetApp solution enables block-level backup and restore from ONTAP to StorageGRID?

27. Which two commands could be used if the cf giveback command foils? (Choose 2)

28. Snapshot copies for SnapLock volumes are deleted automatically according to the retention count set in the Snapshot schedule.

29. How would you initiate a cluster takeover of filer2 from filer 1?

30. Which SyncMirror command mirrors an existing unmirrored aggregate where Data ONTAP selects the disk drives?

31. In cluster takeover mode, the shared interface assumes the identity of the

32. Which native ONTAP feature allows an administrator to block a Windows user from writing files with the.crypto extension?

33. Which one of the following is a recommended secondary system for SnapVault?

34. The OSSV agent on the primary system listens to TCP port 10000 for all SnapVault communications.

35. Which one of the following is not a pre-requisite for using SnapRestore?

36. Which NetApp SnapMirror method allows for transparent failover between two AFF clusters with applications using iSCSI LUNs?

37. Which one of the following is not recommended as a secondary system for SnapVault?

38. What are two logical network components of ONTAP? (Choose two.)

39. Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pull) data from the source appliance?

40. It is the use of the -Lflag in the snapmirror initialize command and the subsequent successful level 0 transfer that causes the destination volume to become snaplocke?