Aruba Certified Switching Associate (ACSA) V1 Certified HPE6-A41 Dumps V13.02

1. Refer to the exhibit.

What should the network administrator do to permit Switch-1 to route traffic from a client in 10.1.11.0/24 to a client in 10.1.12.0/24?

2. How many operating system image files can a network administrator load on an ArubaOS switch?

3. Refer to the exhibit.

Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2.

How does this affect the MSTP topology?

4. Refer to the exhibit.

The network administrator wants to place contractor clients and employee clients in different broadcast domains.

How should the administrator achieve this goal?

5. Refer to the exhibit.

All of the switches shown in the exhibit are ArubaOS switches.

Where should the network administrator configure an IP helper address of 10.1.1.10?

6. What is the relationship between a wireless client’s data rate and the throughput for the client’s traffic?

7. Refer to the exhibit.

The network consists of two ArubaOS switches with routing disabled.

How should the network administrator configure the link between Switch A and Switch B to ensure that all hosts can communicate to all the other hosts within their respective VLANs?

8. What is one benefit that Aruba AirWave can provide to a customer with ArubaOS switches?

9. An ArubaOS switch operates at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection carries untagged traffic. The administrator wants to use Telnet log in to the switch CLI.

How should the administrator contact the switch and log in?

10. Refer to the exhibit.

A network administrator views the configuration files on an ArubaOS switch and sees the output in the exhibit. The administrator enters this command: Switch# boot system flash primary config config2 After the switch boots, the administrator makes some configuration changes and saves the configuration with the write memory command. The administrator then enters this command: Switch# boot After the switch boots, the configuration changes just made are not present.

How can the administrator restore the configuration with the changes?

11. For which task does a network administrator need to access the enable context on an ArubaOS switch?

12. A network administrator prepares an ArubaOS switch to be monitored and managed by AirWave.

Which credentials are required for AirWave to change configuration settings on the switch?

13. A company has an Aruba 5400R switch, switch 1, at the network core of its campus. This switch routes all traffic for the campus and is the RSTP root. The company now wants to add another Aruba 5400R switch to the core in order to enhance resiliency. The company wants to use the option that provides the best Layer 2 and Layer 3 resiliency and also the simplest setup.

What should the administrator do to add the new 5400R switch?

14. Which settings should match on physical interfaces before a network combines them in a link aggregation?

15. Two switches are members of a Virtual Switching Framework (VSF) fabric.

Which statement correctly describes how the switches handle routing?

16. A server connects to a port on an ArubaOS switch. The network administrator wants to ensure that the port remains forwarding during MSTP topology changes, and changes in the port status do not cause MSTP topology changes.

Which statement describes how the administrator can accomplish this?

17. Refer to the exhibit.

Endpoint A sends broadcast ARP requests. Where are these requests received?

18. A network administrator wants to be able to access an Aruba Instant cluster at the same IP address even if the current master fails.

How can the administrator achieve this goal?

19. A network administrator discovers and then authorizes several ArubaOS switches in Aruba AirWave. Immediately after the administrator authorizes the switches, AirWave cannot communicate with the switches anymore.

What should the administrator do to restore communication?

20. A company has a single routing protocol environment.

What is one reason to use OSPF routing instead of static routing?

21. Refer to the exhibit.

A network administrator installs a new aggregation and access layer in a campus network. All users in this area belong to the same VLAN. The administrator plugs the switches into the network with the factory default configurations.

Which protocol must the administrator configure to prevent broadcast storms?

22. A network administrator is in the context in an ArubaOS switch CLI:

Switch (vlan10)#

The administrator wants to leave the configuration context with a single command/

Which command should the administrator enter?

23. Refer to the exhibit.

MSTP is implemented in the topology shown in the exhibit, and all the switches are in the same region. The network administrator does not want to use the Internal Spanning Tree (IST) or instance 0 for production traffic.

How many non-IST spanning tree instances does this network need in order to have effective load sharing on the uplinks from the access switches?

24. Refer to the exhibit.

Based on the exhibit, what is the problem?

25. Refer to the exhibit.

Exhibit 1.

Exhibit 2.

Exhibit 3.

How many MSTP regions exist in the topology shown in the exhibit?

26. An ArubaOS switch operates at factory default settings.

A network administrator enters this command:

Switch (config)# password operator plaintext mysecret.

How does the switch now control access to the CLI through the console port?

27. Refer to the exhibit.

Device 1 needs to send traffic to Device 2, and it sends an ARP request in preparation.

Which devices process this ARP request?

28. A Virtual Switching Framework (VSF) fabric is configured to use LLDP-MAD.

Which action does the standby member take if it sends a probe but receives no response?

29. Refer to the exhibit.

Exhibit 1.

Exhibit 2.

A network administrator needs to set up DHCP relay in a switched network comprised of ArubaOS switches. Switch A and Switch B have the IP settings in Exhibit 2, and no static or dynamic routes. Switch B is the DCHP server’s default gateway. The administrator correctly configures the IP helper address on Switch A.

However, when the DHCP client attempts to acquire an IP address in VLAN 10, the process fails.

What does the administrator need to do to solve this problem?

30. A network administrator configures OSPF in a network with ArubaOS switches. The administrator is concerned that a rogue device might connect to an access layer switch and introduce OSPF routes to the company’s routing topology. The access VLANs do not contain additional routers.

What should the administrator do so switches do not form an adjacency with rogue devices on the access VLANs?

31. A network administrator has copied new software to an ArubaOS switch and placed this software in the secondary flash location. The switch is currently booting from the primary location. The administrator wants the switch to start using the new software.

What should the administrator do to accomplish this?

32. Which security benefit does SNMPv3 offer that SNMPv2 does not offer?

33. The network administrator wants to know which device, type, and manufacturer is connected to port 10 on an Aruba 3810 switch.

Which command could provide this information?

34. Which benefit does Aruba Clarity in Aruba AirWave provide?

35. A Virtual Switching Framework (VSF) fabric currently has two members and two physical 10GbE links in its VSF link.

Which administrative task can a network administrator perform on this VSF fabric when both members are online?

36. Refer to the exhibit.

Based on the topology shown in the exhibit, which symptom does a network administrator see if the ArubaOS switches are in their factory default states?

37. Refer to the exhibit.

Exhibit 1.

Exhibit 2.

PC1 cannot reach PC2.

Based on the exhibits, what could be the cause of this issue?

38. What does the traceroute command that is entered on an ArubaOS switch identify?

39. Refer to the exhibit.

Switch 1 shown in the exhibit is an ArubaOS switch that has an uplink to the network core on interface 25. The network administrator wants to add a link on interface 26.

The administrator creates a link aggregation with this command:

Switch1 (config)# trunk 25-26 trk1 lacp

What else must the administrator do to enable the Switch 1 link aggregation to successfully pass all traffic to the core?

40. Refer to the exhibit.

A network administrator wants to set up a link aggregation between two switches, as shown in the exhibit. The link aggregation must meet these requirements:

Protects against misconfiguration

Can be configured with VLAN and other settings.

Which type of link aggregation should the administrator create?

41. Refer to the Exhibit:

Which issue could cause the Blocked status on A2?

42. Refer to the exhibit.

Assume that Student A’s ARP table is empty. Student A is preparing to send an FTP packet to FTP Server B and needs to discover the proper destination MAC address.

For which IP address does Student A send an ARP request?

43. An ArubaOS switch provides PoE+ several Aruba APs. Users might also connect PoE devices to the is switch. In a situation where the switch PoE capacity is exceeded, the network administrator wants to ensure that the switch continues to power the IPs in preference to other devices.

What should the administrator do to achieve this goal?

44. A network administrator wants to use Aruba AirWave to manage Aruba 3810 Series switches deployed at the campus access layer.

How does AirWave determine which configuration template to apply to these switches?