Get the Most Updated NSE6_SDW_AD-7.6 Dumps (V9.02) to Make Preparations – Come Here to Check the NSE6_SDW_AD-7.6 Free Dumps (Part 1, Q1-Q40) First

Completing the globally recognized Fortinet NSE 6 – SD-WAN 7.6 Enterprise Administrator (NSE6_SDW_AD-7.6) exam not only validates your expertise in SD-WAN and Secure Access Service Edge solutions but also opens doors to better career opportunities and professional growth. When preparing for your exam, you can choose a reliable resource from DumpsBase. We have updated the NSE6_SDW_AD-7.6 dumps to V9.02, offering 257 practice questions and answers to ensure you study smarter, focus on high-yield topics, and build the confidence needed to pass on your first attempt. All these updated practice questions are designed according to the current exam syllabus. Choose DumpsBase updated NSE6_SDW_AD-7.6 dumps (V9.02) today and take a confident step toward achieving your Fortinet NSE 6 certification goals. From today, you can check our NSE6_SDW_AD-7.6 free dumps to verify the most updated version.

Today, the NSE6_SDW_AD-7.6 free dumps (Part 1, Q1-Q40) of V9.02 are available for checking first:

1. Which three protocols can be used for the status check in a performance SLA? (Choose three.)

SSH

DNS

traceroute

TWAMP

HTTP

2. Refer to the exhibit.





Which two statements about the debug output are correct? (Choose two.)

The debug output shows per-IP shaper values and real-time readings.

This traffic shaper drops traffic that exceeds the set limits.

Traffic being controlled by the traffic shaper is under 1 Kbps.

FortiGate provides statistics and reading based on historical traffic logs.

3. Refer to the exhibits, which show the VPN configuration on a spoke and a hub.









The administrator wants to use those tunnels to build an SD-WAN topology.

Which one parameter must you modify to allow the tunnel to come up and be used in the SD-WAN topology?

Set exchange-interface-ip to enable on the hub side.

Change ike-version to 2 on the hub and the spoke.

Set the type to dynamic on the hub side.

Set mode-cfg to enable on the spoke side.

4. Refer to exhibits.









Exhibit A, which shows the SD-WAN performance SLA and exhibit B shows the health of the participating SD- WAN members.

Based on the exhibits, which statement is correct?

The dead member interface stays unavailable until an administrator manually brings the interface back.

Port2 needs to wait 500 milliseconds to change the status from alive to dead.

The SLA state of port2 has exceeded three consecutive unanswered requests from the SLA server.

Check interval is the time to wait before a packet sent by a member interface is considered as lost.

5. Refer to the exhibit.





Based on the exhibit, which two actions does FortiGate perform on traffic passing through port2? (Choose two.)

FortiGate does not change the routing information on existing sessions that use a valid gateway, after a route change.

FortiGate performs routing lookups for new sessions only, after a route change.

FortiGate always blocks all traffic, after a route change.

FortiGate flushes all routing information from the session table, after a route change.

6. An administrator is troubleshooting VoIP quality issues that occur when calling external phone numbers. The SD-WAN interface on the edge FortiGate is configured with the default settings, and is using two upstream links. One link has random jitter and latency issues, and is based on a wireless connection.

Which two actions must the administrator apply simultaneously on the edge of FortiGate to improve VoIP quality using SD-WAN rules? (Choose two.)

Select the corresponding SD-WAN balancing strategy in the SD-WAN rule.

Choose the suitable interface based on the interface cost and weight.

Use the performance SLA targets to detect latency and jitter instantly.

Place the troublesome link at the top of the interface preference list.

Configure an SD-WAN rule to load balance all traffic without VoI

7. Why is it effective to use SD WAN rules when configuring application control?

Because SD-WAIM rules are independent from firewall policies to avoid controlling applications

Because the application database is manually maintained by administrators

Because you must use certificate full inspection on the firewall policy

Because traffic can be load balanced based on application type

8. Refer to Exhibit:





Based on the exhibit, which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules, among the member interfaces?

All traffic from a source IP to a destination IP is sent to the least used interface.

All traffic from a source IP is sent to the same interface.

All traffic from a source IP to a destination IP Is sent to the same interface.

All traffic from a source IP Is sent to the most used Interface.

9. What is the purpose of configuring SD-WAN members?

To provide direct internet access to branch sites

To measure and report application performance

To route traffic between branch sites

To provide access to cloud applications

10. Which command can be used to verify the configuration of SD-WAN members?

show config members

show members config

show running members

show members running

11. Refer to the exhibit.





Which conclusion about the packet debug flow output is correct?

The packet size exceeded the outgoing interface MT

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.

The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

12. By default, what member information does FortiGate consider when selecting the best member in a lowest cost (SLA) SD-WAN rule?

Status of configured SLA targets, cost, and priority

Status of configured SLA targets, interface index number, and priority

Interface index number, cost, and priority

Status of configured SLA targets, cost, and corrected metric

13. Refer to the exhibits.

Exhibit A





Exhibit B





Exhibit A shows the source NAT (SNAT) global setting and exhibit B shows the routing table on FortiGate.

Based on the exhibits, which two actions does FortiGate perform on existing sessions established over port2, if the administrator increases the static route priority on port2 to 20? (Choose two.)

FortiGate flags the sessions as dirty.

FortiGate continues routing the sessions with no SNAT, over port2.

FortiGate performs a route lookup for the original traffic only.

FortiGate updates the gateway information of the sessions with SNAT so that they use port1 instead of port2.

14. Refer to the exhibit.





The administrator used the SD-WAN overlay template to prepare an IPsec tunnel configuration for a hub-and-spoke SD-WAN topology. The exhibit shows the FortiManager installation preview for one FortiGate device.

Based on the exhibit, which statement best describes the configuration applied to the FortiGate device?

It is a spoke device. It can trigger the establishment of an ADVPN shortcut.

It is a hub device in a dual-hub topology. It can participate in the establishment of ADVPN shortcuts.

It is a spoke device. It can establish shortcuts only if the remote spoke initiates the request.

It is a hub device. It will automatically discover the spoke devices and add them to the SD-WAN topology.

15. Which statement is correct about the SD-WAN and ADVPN?

Spoke supports dynamic VPN as a static interface.

Dynamic VPN is not supported as an SD-WAN interface.

ADVPN interface can be a member of SD-WAN interface.

Hub FortiGate is limited to using ADVPN as an SD-WAN member interface.

16. What are two common use cases for remote internet access (RIA)? (Choose two.)

Provide direct internet access on spokes

Provide internet access through the hub

Centralize security inspection on the hub

Provide thorough inspection on spokes

17. Which statement defines how a per-IP traffic shaper of 10 Mbps is applied to the entire network?

The 10 Mbps bandwidth is shared equally among the IP addresses.

Each IP is guaranteed a minimum 10 Mbps of bandwidth.

FortiGate allocates each IP address a maximum 10 Mbps of bandwidth.

A single user uses the allocated bandwidth divided by total number of users.

18. Which command can be used to verify the connectivity between SD-WAN members?

traceroute

ping

netstat

route

19. Which three parameters are available to configure SD-WAN rules? (Choose three.)

Application signatures

Incoming interface

Internet service database (ISDB) address object

Source and destination IP address

Type of physical link connection

20. Refer to the exhibit.





The exhibit shows the SD-WAN rule status and configuration.

Based on the exhibit, which change in the measured packet loss will make T_INET_1_0 the new preferred member?

When all three members have the same packet loss.

When T_INET_0_0 has 4% packet loss.

When T_INET_0_0 has 12% packet loss.

When T_INET_1_0 has 4% packet loss.

21. Refer to the exhibit.





The exhibit shows the details of a session and the index numbers of some relevant interfaces on a FortiGate appliance that supports hardware offloading.

Based on the information shown in the exhibits, which two statements about the session are true? (Choose two.)

The reply direction of the asymmetric traffic flows from port2 to port3.

The auxiliary session can be offloaded to hardware.

The original direction of the symmetric traffic flows from port3 to port2.

The main session cannot be offloaded to hardware.

22. Refer to the exhibits.









Exhibit A shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.

Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?

port2 is referenced in a static route.

port1 and port2 are not administratively down.

port1 is referenced in a firewall policy.

port1 is assigned a manual IP address.

23. Which components make up the secure SD-WAN solution?

FortiGate, FortiManager, FortiAnalyzer, and FortiDeploy

Application, antivirus, and URL, and SSL inspection

Datacenter, branch offices, and public cloud

Telephone, ISDN, and telecom network

24. What are two roles that SD-WAN orchestrator plays when it works with FortiManager? (Choose two.)

It configures and monitors SD-WAN networks on FortiGate devices that are managed by FortiManager.

It acts as a standalone device to assist FortiManager to manage SD-WAN interfaces on the managed FortiGate devices.

It acts as a hub FortiGate with an SD-WAN interface enabled and managed along with other FortiGate devices by FortiManager.

It acts as an application that is released and signed by Fortinet to run as a part of management extensions on FortiManager.

25. If the outgoing interface for an established SNA Ted session changes, which two requirements must the configuration meet so that FortiGate continues forwarding packets from that session to the new outgoing interface? (Choose two.)

You must have a firewall policy that accepts the new traffic flow for the session.

You must configure FortiGate so the SNAT IP address doesn’t change.

You must enable the snat-route-change setting.

You must set firewall-session-dirty to check-new on the new matching firewall policy.

26. Which SD-WAN routing protocol is commonly used for hybrid SD-WAN deployments?

Border Gateway Protocol (BGP)

Open Shortest Path First (OSPF)

Routing Information Protocol (RIP)

Enhanced Interior Gateway Routing Protocol (EIGRP)

27. What is the purpose of configuring SD-WAN route policies?

To configure routing protocols

To configure security policies

To configure application performance monitoring

To configure VPN connectivity

28. Refer to the exhibits.









The VPN configuration on a spoke and a hub is shown.

The administrator wants to use those tunnels to build an SD-WAN topology.

Which one parameter must you modify to allow the tunnel to come up and be used in the SD-WAN topology?

Set exchange-interface-ip to enable on the hub side.

Set mode-cfg to enable on the spoke side.

Change ike-version to 2 on the hub and the spoke.

Set the type to dynamic on the hub side.

29. Refer to exhibits.









Exhibit A shows the SD-WAN rules and exhibit B shows the traffic logs. The SD-WAN traffic logs reflect how FortiGate processed traffic.

Which two statements about how the configured SD-WAN rules are processing traffic are true? (Choose two.)

The implicit rule overrides all other rules because parameters widely cover sources and destinations.

SD-WAN rules are evaluated in the same way as firewall policies: from top to bottom.

The All_Access_Rules rule load balances Vimeo application traffic among SD-WAN member interfaces.

The initial session of an application goes through a learning phase in order to apply the correct rule.

30. Which component in a hub-and-spoke IPsec topology serves as the central point of management and configuration?

The hub site

The spoke sites

The VPN server

The firewall

31. What is the purpose of configuring SD-WAN path control?

To configure routing protocols

To configure security policies

To configure application performance monitoring

To ensure traffic takes the most optimal path

32. In which rule strategy are cost and interface preference not considered selection factors?

Best Quality

Lowest Cost (SLA)

Maximize Bandwidth (SLA)

Manual

33. Which SD-WAN traffic shaping technique prioritizes critical applications and limits bandwidth for non-critical applications?

Quality of Service (QoS)

Link steering

Application steering

Load balancing

34. Which statement is correct about SD-WAN and ADVPN?

Routes for ADVPN shortcuts must be manually configured.

SD-WAN does not monitor the health and performance of ADVPN shortcuts.

You must use OSP

SD-WAN can steer traffic to ADVPN shortcuts established over IPsec overlays configured as SD-WAN members.

35. Which two statements correctly describe what happens when traffic matches the implicit SD-WAN rule? (Choose two.)

The session information output displays no SD-WAN service I

FortiGate flags the session with sdw-imp.

The traffic is distributed through only static routes or directly connected routes.

By default, FortiGate load balance the traffic according to the source IP address.

36. Refer to exhibits.









Exhibit A shows the performance SLA exhibit B shows the SD-WAN diagnostics output.

Based on the exhibits, which statement is correct?

Port1 became dead because no traffic was offload through the egress of port1.

SD-WAN member interfaces are affected by the SLA state of the inactive interface.

Both SD-WAN member interfaces have used separate SLA targets.

The SLA state of port1 is dead after five unanswered requests by the SLA servers.

37. Which two features are supported by IKEv2 and not by IKEv1? (Choose two.)

Asymmetric authentication

IKE mode configuration

IKE aggressive mode

Network overlay ID

38. What is the purpose of configuring SD-WAN route filters?

To filter traffic based on applications

To filter traffic based on IP addresses or subnets

To configure security policies

To configure application performance monitoring

39. Which are two benefits of using CLI templates in FortiManager? (Choose two.)

You can reference meta fields.

You can configure interfaces as SD-WAN members without having to remove references first.

You can configure FortiManager to sync local configuration changes made on the managed device, to the CLI template.

You can configure advanced CLI settings.

40. In a hub-and-spoke SD-WAN topology, you choose OaaS for your overlays.

What type of routing can you use on the branches?

Static routing on the overlay network and static routing on the underlay and between the branch-protected subnets.

BGP routing on the overlay network and static routing on the underlay and between the branch-protected subnets.

Static routing on the overlay network and BGP routing on the underlay and between the branch-protected subnets.

OSPF routing on the overlay network and OSPF routing on the underlay and between the branch-protected subnets.

 Loading...