Practice 300-410 Dumps (V29.02) to Prepare for Your Exam: Check 300-410 Free Dumps (Part 2, Q41-Q80) Online

1. DRAG DROP

Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

2. Which two protocols can cause TCP starvation? (Choose two)

3. Which transport layer protocol is used to form LDP sessions?

4. An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install.

Which command must the engineer run to correct the configuration?

5. Which IGPs are supported by the MPLS LDP autoconfiguration feature?

6. Which protocol does MPLS use to support traffic engineering?

7. Refer to the exhibit.

An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries.

Which action ensures consistency between the two times?

8. Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?

9. Refer the exhibit.

Which action resolves intermittent connectivity observed with the SNMP trap packets?

10. Refer to the exhibit.

In which circumstance does the BGP neighbor remain in the idle condition?

11. What is the output of the following command:

show ip vrf

12. A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic.

Which command should the engineer use to complete this action?

13. Refer to the exhibit.

The ACL is placed on the inbound Gigabit 0/1 interface of the router. Host 192.168.10.10cannot SSH to host 192.168.100.10 even though the flow is permitted.

Which action resolves the issue without opening full access to this router?

14. DRAG DROP

Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

15. Which component of MPLS VPNs is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?

16. Refer to the exhibit.

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route.

Which action blocks the route?

17. Refer to the exhibit.

A company is evaluating multiple network management system tools. Trending graphs generated by SNMP data are returned by the NMS and appear to have multiple gaps. While troubleshooting the issue, an engineer noticed the relevant output.

What solves the gaps in the graphs?

18. Which protocol does VRF-Lite support?

19. Which two statements about VRF-Lite configurations are true? (Choose two.)

20. Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network.

Which configuration prevents this loop?

A)

B)

C)

D)

21. DRAG DROP

Drag and drop the packet types from the left onto the correct descriptions on the right.

22. Refer to the exhibit.

An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed.

What is the reason for this issue?

23. 1.Refer to the exhibit.

Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet.

Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

24. DRAG DROP

Drag and drop the MPLS VPN device types from me left onto the definitions on the right.

25. Refer to the exhibit.

The network administrator configured VRF lite for customer A. The technician at the remote site misconfigured VRF on the router.

Which configuration will resolve connectivity for both sites of customer_a?

26. Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?

27. Refer to the following output:

Router#show ip nhrp detail

10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47

Type. dynamic, Flags: authoritative unique nat registered used

NBMA address: 10.12.1.2

What does the authoritative flag mean in regards to the NHRP information?

28. Which list defines the contents of an MPLS label?

29. Which is statement about IPv6 inspection is true?

30. Refer to the exhibit.

An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen.

What is the reason for this?

31. Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3.

What is the reason the route is not advertised?

32. Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

33. Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690.

What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

34. An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency.

The output of the show ip ospf neighbor command shows that the neighbor state is EXSTART/EXCHANGE.

Which action should be taken to resolve this issue?

35. Refer to the exhibit.

An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock.

What is the reason for this error?

36. Refer to the exhibit.

Which control plane policy limits BGP traffic that is destined to the CPU to 1 Mbps and ignores BGP traffic that is sent at higher rate?

37. Refer to the exhibit.

Which two actions should be taken to access the server? (Choose two.)

38. Refer to the exhibit.

An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting.

Which command must be used in configuration mode to enable SSH on the device?

39. Which statement about IPv6 RA Guard is true?

40. Refer to the exhibit.

A junior engineer updated a branch router configuration. Immediately after the change, the engineer receives calls from the help desk that branch personnel cannot reach any network destinations.

Which configuration restores service and continues to block 10.1.1.100/32?