NS0-165 Dumps (V8.02) with NCDA Exam Questions – Read NetApp NS0-165 Free Dumps (Part 1, Q1-Q40) Today

1. What command would you enter to restore the /vol/flexvol0/etc/rc file from a snapshot to the /vol/flexvol0/home directory?

2. Which native ONTAP feature allows an administrator to block a Windows user from writing files with the.crypto extension?

3. To remove a cluster setup, you must perform the following steps.

1. Type cf disable.

2. Unlicense cluster.

3. Remove partner entries for network interfaces from the /etc/rc file.

4. Halt and make sine the partner-sysid is blank.

5. Power down and remove the cluster interconnect card.

6. Perform steps 1-5 above on the partner node.

4. Which one of the following actions will cause a currently in sync snapmirror relationship to fall out of sync?

5. Which one of the following is not a pre-requisite for using SnapRestore?

6. Due to the sensitive nature of AutoSupport messages, what transport protocol should a storage administrator configure?

7. Five minutes ago, you performed a single file SnapRestore on a large NFS file. 40% of your NFS users are now complaining about getting "stale file handles" for the file.

Which one of the following is the most likely cause of this problem, and the best procedure to correct it?

8. Which one of the following statements apply to the Free Space Estimator utility?

9. It is the use of the -Lflag in the snapmirror initialize command and the subsequent successful level 0 transfer that causes the destination volume to become snaplocke?

10. Which command displays the disk ownership for both CPU modules in a FAS270C appliance?

11. Which two options must be configured to use tamperproof snapshots? (Choose two.)

12. An administrator has an existing FlexVol accessed by Linux hosts over NFSv3. A CIFS share to the same FlexVol was created for SMB access. Windows users are unable to view the share. CIFS share permissions allow for read and write access for the Windows users.

What does the administrator need to modify to allow SMB access?

13. If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank

14. Identify the two SnapMirror commands that are entered on the destination storage appliance.

15. The SnapVault secondary system allows you to keep a separate schedule of Snapshot copies from your primary system.

16. After you use SnapRestore to revert a volume to a specific snapshot,….

17. The OSSV agent on the primary system listens to TCP port 10000 for all SnapVault communications.

18. Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner node, Node 2, can see all of Node 1s disk shelves.

Which one of the following features will cause Node 2 to monitor this error condition for a period of three minutes (by default), and then forcibly take over Node 1 if the error condition persists?

19. Which three tools present statistics from the Data ONTAP counter manager? (Choose three.)

20. Which two tools can be used to actively monitor ONTAP cluster performance? (Choose two.)

21. Snapshot copies for SnapLock volumes are deleted automatically according to the retention count set in the Snapshot schedule.

22. Which two Interfaces can an administrator use to disable unused Ethernet ports on an ONTAP cluster? (Choose two.)

23. Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?

24. For aggregates or traditional volume SyncMirror to work correctly, the configuration of each plex must be identical with regard to____________.

25. Which one of the following is not a pre-requisite for using SnapRestore?

26. Which two products can be used to administer Cloud Volumes ONTAP? (Choose two.)

27. A mirrored volume has a failed disk, but there are no available spares in the pool from which the degraded plex was built. Data ONTAP will:

28. The snapvault update command is only available on the secondary system.

29. You can unlicense the cluster feature only in

30. For a configuration change to be effective when using the OSSV configurator, the OSSV service must be restarted.

31. Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?

32. In a Fabric Attached Metro Cluster, disk ownership by a node is determined by_____________.

33. In cluster takeover mode, the shared interface assumes the identity of the

34. Which SyncMirror command mirrors an existing unmirrored aggregate where Data ONTAP selects the disk drives?

35. Which OSSV package would you use to perform an OSSV unattended installation?

36. Which statement describes the results of the snapmirror resync command?

37. The required hardware to add SyncMirror to an existing system would be ___________.

38. Which two configurations ensure end users are able to restore previous versions of files? (Choose two.)

39. You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is

40. Which NetApp solution enables block-level backup and restore from ONTAP to StorageGRID?