NetApp Certified Implementation Engineer – SAN Specialist, E-Series NS0-516 Dumps

1. What would be the minimum configuration required to support a drawer-protected 20-drive DDP? (Choose the best answer.)

2. What uses the Access Volume? (Choose the best answer.)

3. What is a NetApp best practice recommendation for the system monitor?

4. What are two types of logical structures that volumes in the E-Series system use? (Choose two.)

5. When data is written to a snapshot, volume is stored __________. (Choose the best answer.)

6. Exhibit:

Referring to the exhibit, what is the total number of ALUA paths from the host to a volume on the EF280?

7. Witch function does the SANtricity Enterprise Management Window (EMW) provide? (Choose the best answer.)

8. Hot spares provide which function? (Choose the best answer.)

9. What are two base host connectivity selections that are provided by the E2800 controller? (Choose two.)

10. Which file contains the configuration for a multipath driver for FC on Linux systems?

11. If an FDE disk fails, which characteristic is required of the replacement disk?

12. Exhibit:

Which fiber cable end shown in the exhibit is supported on a NetApp E-Series system?

13. Exhibit:

You ordered a NetApp E2812 Duplex 16GB 10GbE Base-T system.

Referring to the exhibit, what is the maximum number of 10GbE Base-T ports available to be used?

14. What is the SANtricity Client? (Choose the best answer.)

15. Which support data file provides a description of all the hardware, logical components, and properties of the storage system?

16. A customer has an E-Series system with several expansion enclosures and can use the ______ to determine if the connections between the enclosures have been cabled correctly. (Choose the best answer.)

17. Which feature under SANtricity 11.x which requires an activation key? (Choose the best answer.)

18. What mechanism governs control of the E-Series storage premium features? (Choose the best answer.)

19. The interval for an asynchronous mirror group should usually be equal to ______________. (Choose the best answer.)

20. What measurement refers to how much data can be handled in a given time period? (Choose the best answer.)

21. During a routine review of firewall logs, an analyst identified that an IP address from the organization’s server subnet had been connecting during nighttime hours to a foreign IP address, and had been sending between 150 and 500 megabytes of data each time. This had been going on for approximately one week, and the affected server was taken offline for forensic review.

Which of the following is MOST likely to drive up the incident’s impact assessment?

22. Which three factors should you consider before you install an E2860 in a data center? (Choose three)

23. What does the storage system use to preserve cache data in the event of a complete controller failure? (Choose the best answer.)

24. You are troubleshooting a customer issue on their E-Series system. You need information on the volume configuration of the customer's system.

In this scenario, which log would you download to get the required information?

25. Which feature used on E-Series controllers enables them to ship I/O to the alternate controller?

26. An administrator is asked to provision a 1 TB volume to hold non-critical temporary data for a seismic-analysis application. The volume requires the highest possible IOPS.

In this scenario, which configuration would satisfy this requirement?

27. Which two local users of NetApp SANtricity Unified Manager would be used to edit the Certificate Management section? (Choose two.)

28. Which NetApp tool provides information on size, weight, acoustic noise, and power of NetApp E-Series systems?

29. With a system cache block size of 32K, how much cache space per I/O is “lost” if incoming I/Os are all 48K writes? (Choose the best answer.)

30. In SANtricity System Manager, the Recovery Guru reports a loss of paths to an iSCSI host.

In this scenario, which tool would you use to troubleshoot this issue?

31. If you have to replace the battery on a controller, you should put the controller into which state?

32. To discover events that need to be reported to the storage administrator, which log does the Event Monitor poll?

33. Your company has an E-Series system connected to Cisco MDS switches. You are asked to provision a volume on a new Windows host, but the Windows host is unable to connect to the volume on the E-Series system. All other Windows hosts in the fabric are able to connect to their volumes.

In this scenario, which three actions should you perform to accomplish this task? (Choose three.)

34. Which two actions must be performed to enable iSCSI multipathing on Windows for NetApp E-Series systems? (Choose two.)

35. Exhibit:

Referring to the exhibit, what would you select in the search list to see all of the host selections for NetApp ESeries storage systems?

36. Synchronous mirroring requires what type of connection between storage systems? (Choose the best answer.)

37. In the AMW, which tab provides access to Ethernet management port configuration and premium feature enablement? (Choose the best answer.)

38. What happens if one disk chosen for a volume group has a capacity of 2 TB and the other five disks have a capacity of 4 TB?

39. What is the ‘base’ host connectivity provided by the E5500 Controller? (Choose the best answer.)

40. What is the ‘base’ host connectivity provided by the E2600 controller? (Choose the best answer.)

41. Where does the explicit multipath driver reside?

42. You are helping a customer diagnose a performance issue on an E-Series storage system. You decide to measure the amount of data that is being handled over the span of an hour.

In this scenario, what are you measuring?

43. You are setting-up asynchronous mirroring between two E2860 systems.

In this scenario, which two prerequisites are required to complete the setup? (choose two)

44. Where would you find the version of the driver and firmware for QLogic HBAs that are supported by NetApp E-Series systems?

45. What four resources have information to determine space and power & cooling requirements for E-Series storage systems? (Choose four.)

46. What SANtricity package(s) must be installed on a Windows server when it is acting as both a data host and a storage management host?

47. What is the ‘base’ host connectivity provided by the E5400 Controller? (Choose the best answer.)

48. Which item can be downloaded concurrently with controller firmware? (Choose the best answer.)

49. Which alerting method would be configured using the SANtricity System Manager setup wizard?

50. An administrator is asked to migrate two DE6600 shelves into a newly deployed E5760 environment that is configured with a stack of two DE460C shelves.

In this scenario, how does the administrator complete this task?

51. A d-stripe within a disk pool is always the equivalent of _______. (Choose the best answer.)

52. What is a best practice recommendation for the automated system monitor? (Choose the best answer.)

53. Exhibit:

A customer’s host is running a Red Hat Enterprise Linux 7.6 server with dm-mp configured for ALUA and is connected to a single volume on the EF280 system that is shown in the exhibit.

In this scenario, how many active/optimized paths are available to the volume?

54. Which component of an E-Series storage system should always be upgraded first? (Choose the best answer.)

55. In the storage manager client, what are host groups? (Choose the best answer.)

56. How many 32 Gb ports are on one FC host interface card (HIC) on the NetApp E2800, EF280, E5700, and EF570 systems?

57. Controller firmware package files start with which character(s)? (Choose the best answer.)

58. Exhibit:

Referring to the exhibit, which cable is an InfiniBand 4X connector?

59. What happens if you choose one disk that has a capacity of 300 GB and five others that have a capacity of 900 GB for a volume group? (Choose the best answer.)

60. Your AutoSupport does not automatically send reports to NetApp’s ActiveIQ tool.

In this scenario, how do you access the data that would have been sent using the AutoSupport feature?