GB0-382-ENU Exam Dumps (V8.02) – Secure Your H3C Certified Senior Engineer for Routing & Switching Plus (H3CSE-RS+) Certification with DumpsBase

You need to pass the GB0-382 Advanced Routing & Switching Technology 2 exam to secure your H3C Certified Senior Engineer for Routing & Switching Plus (H3CSE-RS+) certification with confidence. We have completed the GB0-382-ENU exam dumps (V8.02) with 528 practice questions and answers for learning. All these questions and answers are in English, helping you practice well. Curated by seasoned industry professionals, our GB0-382-ENU exam questions are meticulously and continuously updated to align with the latest H3C standards, technological advancements, and shifting syllabus requirements. By moving beyond simple rote memorization, DumpsBase delivers realistic exam simulations that perfectly mirror the actual testing environment. Choose DumpsBase GB0-382-ENU exam dumps (V8.02) to transform your preparation into a complete learning experience that seamlessly bridges the gap between certification readiness and real-world workplace mastery.

Check GB0-382-ENU free dumps below to check the quality first:

1. The advantages of modular network architecture include ().
2. Which of the following routing protocols supports VLSM but not automatic route aggregation?
3. As shown in the figure, the headquarters' MSR router is connected to the branch office via two 100Mbps Ethernet links. To fully utilize the existing bandwidth resources, which of the following routing schemes is optimal?



4. Execute the following command on the MSR router RTA:

[RTA-GigabitEthernet0/0] ip address 192.168.1.1 24

[RTA-GigabitEthernet0/0] uit

[RTA] router id 2.2.2.2

[RTA] ospf 1 router-id 1.1.1.1

[RTA-ospf-1] uit

[RTA] interface LoopBack 0

[RTA-LoopBack0] ip address 3.3.3.3 32

Based on the above configuration, we can determine that the Router ID of OSPF process 1 in RTA is ().
5. The topology of a certain network is relatively complex, with multiple paths between the core and the branches.

To control routing between the core and branch offices, effectively utilize bandwidth resources, and reduce maintenance costs, which of the following measures is optimal?
6. The command to disable RIP protocol automatic route aggregation on an MSR router is ().
7. The OSI network devices are networked as shown in the diagram. This OSI network contains a total of () ES (hosts).



8. As shown in the figure, the headquarters' MSR router is connected to the branch office via Ethernet interface E1/0, and the connection is backed up via the ISDN network.





Which of the following options are the most reasonable and feasible at this point?
9. The network topology is shown in the diagram. RTA and RTB are located on AS 1001, while RTC, RTD, and RTE are located on AS 1002. AS 1001 advertises the BGP route 11.11.11.0/24 to AS 1002. The main BGP configurations for RTC and RTD are as follows. If the interconnection link between RTE and RTC is interrupted, which WAN link will RTE prioritize using when accessing the 11.11.11.0/24 network segment?

[RTC]

BGP 1002

Preference 20 170 200

PeerRTA as-number 1001

PeerRTD as-number 1002

PeerRTA route-policsetmed import

Route-policsetmed permit node 10

Applcost 100

[RTD]

BGP 1002

Preference 20 170 200

PeerRTB as-number 1001

PeerRTC as-number 1002

PeerRTA route-policsetmed import

Route-policsetmed permit node 10

Applcost 200



10. As shown in the figure, the actual bandwidth of the MSR router's Ethernet interface E1/0 is 10Mbps, and the actual link bandwidth of the serial port S2/0 is 64Kbps.





To prioritize the use of high-bandwidth links and achieve route backup, which of the following solutions is the most reasonable?
11. Which of the following statements about BGP load balancing is correct?
12. An administrator wants to configure an OSPF route priority value of 60 on an MSR router. Which of the following commands is correct?
13. As shown in the figure, a local area network is connected to an ISP via an MSR router. If packet-based routing is to be implemented on the outgoing interface of the MSR router, which configurations are necessary?



14. In a certain network project, the client considered that the number of network users might increase significantly in the future, so they required the network to have good scalability.

Which of the following measures can improve network scalability?
15. There are 4 routes in the routing table: 172.16.0.0/24, 172.16.1.0/24, 172.16.2.0/24, and 172.16.3.0/24.

If you want to perform route aggregation, the correct aggregated route is ().
16. As shown in the figure, the headquarters' MSR router is connected to the branch office via Ethernet interface E1/0, and the connection is backed up via the ISDN network.





Which of the following options are the most reasonable and feasible at this point?
17. L is a network design engineer. In a certain network project, to reduce complexity, L designed a two-layer architecture, integrating the access layer functionality into the aggregation layer. During the design process, L considered that the core layer needed to have fast convergence capabilities, and the aggregation layer would perform route aggregation to reduce the number of routes.

Which of the following routing protocols should Little L use as the core layer routing protocol?
18. As shown in the figure, EBGP runs between AS100, AS200, AS300, and AS400.





When AS400 receives a BGP route from AS100, the path order recorded in its AS-Path attribute is ().
19. In H3C devices, the default priority value for OSPF internal routes is _____.
20. The topology of a certain network is relatively complex, with multiple paths between the core and the branches.

To control routing between the core and branch offices, effectively utilize bandwidth resources, and reduce maintenance costs, which of the following measures is optimal?
21. Routers RTA and RTB have established a BGP connection and learned routes from each other. [Both RTA and RTB use the default timer.]

If congestion occurs on the links between routers, causing the RTA to fail to receive Keepalive messages from the RTB, which of the following consequences will occur?
22. A network is connected to the Internet via a 64kbps wide area network link. The customer requires that the bandwidth of this link be used as efficiently as possible. Then you should use an Internet connection. Which routing method should be implemented to achieve the highest bandwidth efficiency?
23. In the network shown in the figure, dynamic routing protocols are not enabled between any routers; only static routes can be configured.





The correct configuration on the RTE should be ().
24. An administrator wants to configure a RIP route priority value of 60 on an MSR router. Which of the following commands is correct?
25. Which of the following are functions of a convergence layer?
26. The default priority value for OSPF external routes is ().
27. There are 4 routes in the routing table: 192.168.0.0/24, 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24.

If you want to perform route aggregation, the correct aggregated route is ().
28. A router has RIP protocol enabled, process ID 1, priority 10; and OSPF protocol enabled, process ID 100, priority 100. If both processes learn routes to the 10.0.0.0/8 network segment simultaneously, with metrics of 1 (hop count) and 100 (cost), their next hops are 1.0.0.1 and 1.0.0.2, respectively.

How should a router process a packet destined for 10.0.0.1?
29. Dynamic routing protocols are not enabled between any routers; only static routes can be configured.





The correct configuration on the RTE should be ().
30. SOA-based network architecture divides enterprise IT systems into which of the following layers?
31. An administrator wants to configure an OSPF route priority value of 100 on an MSR router. Which of the following commands is correct?
32. A router has RIP protocol enabled with priority 10 and OSPF protocol enabled with priority 100. If both protocols learn the route 10.0.0.0/8 at the same time, with metrics of 1 (hop count) and 100 (cost) respectively, the next hops will be 1.0.0.1 and 1.0.0.2 respectively.

How should the router process a packet destined for 10.0.0.1?
33. Which of the following statements about IToIP is incorrect?
34. B In the topology shown in the figure, perform the following configuration in RTA.

[RTA-ospf-1-area-0.0.0.1] network 192.168.0.0 0.0.0.255

[RTA-ospf-1-area-0.0.0.1] network 192.168.1.0 0.0.0.255

[RTA-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255

[RTA-ospf-1-area-0.0.0.1] network 192.168.3.0 0.0.0.255

If the requirement is that the RTC must not learn the routes configured in the RTA, what configurations can be performed on the router?



35. There are 4 routes in the routing table: 10.0.0.0/24, 10.0.1.0/24, 10.0.2.0/24, and 10.0.3.0/24.

If you want to perform route aggregation, the correct aggregated route is ().
36. In the process of generating a fast forwarding table, a quintuple refers to ().
37. RTA is the border router of the OSPF routing domain and the BGP routing domain. If a BGP route with a MED value of 200 is introduced into OSPF on the RTA, the RTB will learn the COST value of () by default.



38. In a certain network project, the client considered that the number of network users might increase significantly in the future, so they required the network to have good scalability.

Which of the following measures can improve network scalability?
39. In the IS-IS network shown in the figure, RTA, RTC, RTD, and RTE establish Level-2 adjacency relationships with each other; RTB establishes Level-1 adjacency relationships with RTA and RTC. After the routing of each router is stable, when RTB accesses 192.168.14.1, it selects the next hop as ().

If the following configurations are added to RTA and RTC respectively at this time :

[ RTA-isis-1] import-route isis level-2 into level-1

[RTC-isis-1] import-route isis level-2 into level-1

So when RTB accesses 192.168.14.1, the next hop is selected as ().



40. Routers RTA and RTB are eBGP neighbors. RTA advertises route 10.10.10.0/24 and sets the community attribute. However, checking RTB's routing table reveals that route 10.10.10.0/24 learned from RTA does not carry the community attribute. What could be causing this loss of the community attribute?
41. In H3C devices, the default priority value for RIP protocol routing is _____.
42. IS-IS periodically sends which of the following messages on P2P type links?
43. Among the following routing protocols, which one belongs to EGP and which one uses the link-state algorithm?
44. Which of the following are characteristics of link-state routing protocols?
45. All relevant 6to4 tunnel configurations are correct. This datagram is received by RTA when it receives an IPv6 packet from PC1 destined for address 2002:303:314:202:206:101:118:1. Which of the following describes how RTA will process and forward this datagram?
46. Among the following routing protocols, the one that belongs to IGP and the one that uses the path vector algorithm are ().
47. Which of the following address prefix lists matches the default route?
48. Among the following routing protocols, the one that belongs to IGP and the one that uses the link-state algorithm are ().
49. A router has enabled the RIP protocol with process ID 1 and priority 100; it also has enabled the OSPF protocol with process ID 100 and priority 10 .

If two processes simultaneously learn routes to the 10.0.0.0/8 network segment, with metric values of 1 (hop count) and 100 (cost) respectively, which process's learned route 10.0.0.0/8 will be added to the IP routing table?
50. As shown in the figure, the headquarters' MSR router is connected to the branch office via two 100Mbps Ethernet links. To fully utilize the existing bandwidth resources, which of the following routing schemes is optimal?




 

GB0-392-ENU Dumps (V8.02) Are Online for Your H3CSE-RS-NSO Certification Exam Preparation - Check GB0-392-ENU Free Dumps (Part 1, Q1-Q40) First
Tags:

Add a Comment

Your email address will not be published. Required fields are marked *