HomeH3CH3CNEUpdated GB0-192-ENU Dumps (V9.02) for Routing and Switching Essentials Exam Preparation – Check GB0-192-ENU Free Dumps (Part 1, Q1-Q40) Today
June 2, 2026

Updated GB0-192-ENU Dumps (V9.02) for Routing and Switching Essentials Exam Preparation – Check GB0-192-ENU Free Dumps (Part 1, Q1-Q40) Today

The GB0-192 Routing and Switching Essentials exam is the qualifying test required to achieve the H3C Certified Network Engineer for Routing & Switching Plus (H3CNE-RS+) certification. It is designed to validate your comprehensive understanding of data communications networking and their ability to plan, design, deploy, and maintain small-to-medium-sized enterprise (SME) networks using H3C equipment. To prepare for this exam effectively in 2026, you can have the most updated GB0-192-ENU dumps (V9.02) from DumpsBase. GB0-192-ENU dumps (V9.02) contain 508 practice questions and answers, which are in English for understanding. Also, they have been verified by certified professionals, providing the competitive edge necessary to confidently pass your Routing and Switching Essentials test and fast-track your professional growth. By immersing yourself in these high-quality, up-to-date H3C GB0-192-ENU dump questions, you can fully master the latest questions and eliminate any surprises on exam day.

Today, we will share GB0-192-ENU free dumps (Part 1, Q1-Q40) of V9.02 below to help you check the quality:

1. If a port running STP in an Ethernet switch does not receive or forward data, but receives and sends BPDU and does not perform address learning, then the port should be in the ( ) state.
2. On an MSR router, by default, the configuration file ends with ().
3. Suppose an MSR router obtains two routes to the destination network segment 100.120.10.25/24. The costs of these two routes are 120 and 10, and their priorities are 10 and 150, respectively.

Then the data packets destined for this address will ( ).
4. During system startup, if you type () as prompted, the system will interrupt the boot process and enter bootrom mode.
5. Two routers, RTA and RTB, are directly connected via their g0/0 ports. RTA's g0/0 IP address is 192.168.1.1/30, and RTB's g0/0 address is 192.168.1.5/24. Which of the following statements is correct?
6. On an MSR router, type the first few letters of a keyword in a command and press ( ) to complete the command.
7. What is the correct configuration command to enable DHCP service on a router?
8. The customer needs to configure two static routes on the router that go to the same destination address to achieve the purpose of mutual backup.

Which of the following statements about the configuration of these two routes is correct?
9. A default route a is configured on an MSR router running OSPF with a next-hop address of 100.1.1.1; at the same time, the router learns a default route b with the same next-hop address of 100.1.1.1 from its neighboring router via OSPF.

This router uses the default priority and cost values for all routing protocols, which of the following is correct?
10. The subnet mask of IP address 132.119.100.200 is 255.255.255.224. Then the IP subnet address it belongs to is ().
11. Suppose an MSR router obtains two routes to the destination network segment 100.120.10.0/24. The costs of these two routes are 120 and 10, and their priorities are 10 and 150, respectively.

The data packets destined for this address will then ( ).
12. In subnetting, which part of the classful IP address space does the subnet number occupy?
13. The IP address 203.108.2.110 is a ( ) address.
14. On an MSR router, to view the files in the recycle bin, you can use the () command.
15. On an MSR router, use the () command to view the router's NAT aging time.
16. The subnet mask of IP address 132.119.100.200 is 255.255.255.240. Then the IP subnet address it belongs to is ().
17. When configuring OSPF on a router, what configurations must be performed manually?
18. The following routing information is seen on an MSR router running RIP:

<msr>display ip routing-table 6.6.6.6

Routing Table: Public

Summary count: 2

destination/mask proto pre cost nexthop interface

6.6.6.0/24 rip 100 1 100.1.1.1 ge0/0

6.0.0.0/8 static 60 0 100.1.1.1 ge0/0

At this moment, the router receives a data packet with a destination address of 6.6.6.6, which of the following is correct?
19. When we receive a used router, we usually need to restore the device to its factory default configuration to prevent the existing configuration from affecting normal use later. We can use the () command to delete the saved next boot configuration file on the device, and then use the reboot command to restart the device. After restarting, since there is no boot configuration file, the device will load its factory default configuration.
20. The main function of the physical layer of the OSI reference model is ().
21. The default data transfer port used by .ftp is ( ).
22. In the network environment shown in the figure, two routers are connected back to back via serial ports. To set the speed of the interconnection link to 2 Mbps, which of the following statements is correct?



23. To configure a static route on a router, given the destination address is 192.168.1.0, the subnet mask is 20 bits, the outgoing interface is gigabitethermet0/0, and the outgoing interface IP address is 10.10.202.1, which of the following configurations are correct?
24. After receiving a DHCP ACK message, if a DHCP client finds that the IP address it is about to use already exists on the network, what message will it send to the DHCP server?
25. Router MSR-1 is interconnected with MSR-2 and MSR-3. MSR-1's routing table contains a RIP route learned from MSR-2 that goes to the destination network segment 120.10.12.0/24, with a cost of 3. At the same time, MSR-1 also receives a RIP route from MSR-3 that goes to the destination network segment 120.10.12.0/24, with a cost of 15. Which of the following is correct?
26. One of the customer's MSR routers is connected to the Internet via the WAN interface S1/0; and to the office network via the LAN interface GE0/0. Currently, office network users can access the Internet normally.

Add the following ACL configuration to the router:

ACL Advanced 3000

rule 0 deny icmp

rule 5 permit tcp destination-port eq 20

interface GigabitEthernet0/0

packet-filter 3000 inbound

packet-filter 3000 outbound

Which of the following is correct?
27. On an MSR router, if you want to download a file from an FTP server, you should use the () command in the FTP commands.
28. Router MSR-1's ge0/0 interface address is 192.168.100.1/24. This interface is connected to a Layer 3 switch, which serves as the default gateway for multiple network segments within the customer's office network. MSR-1 connects to the internet via serial port S1/0. The entire network is interconnected, and office network users can access the internet. For security reasons, it is necessary to prevent customer hosts from pinging MSR-1's ge0/0 interface. Therefore, the following ACL was configured on the router: ACL number 3008 rule 0 deny icmp source 192.168.1.0 0.0.0.255. This ACL is also applied to the inbound direction of ge0/0. However, users in the 192.168.0.0/24 network segment can still ping the ge0/0 interface address.

Based on the information above, we can infer that ( ).
29. The subnet mask of IP address 132.119.100.200 is 255.255.255.224. Then the broadcast address of its subnet is ().
30. Configure static routes on an MSR router using the () command.
31. Two students in a university dormitory want to play online games together. They connect their two computers with a network cable. One student sets his computer's IP address to 192.168.1.1/24. In order for the two computers to connect to the network normally, what IP address can the other student set his computer to?
32. The router discovery function in the IPv6 Neighbor Discovery Protocol refers to ( ).
33. 802.1x defines a port-based network access control protocol, and only defines point-to-point connections between access devices and access ports. The access port can only be a physical port.
34. DNS can use which transport layer protocol?
35. Regarding the compressed representation of the IPv6 address 2001:0410:0000:0001:0000:0001:0000:45ff, which of the following are correct?
36. In the network environment shown in the figure, execute the following NAT configuration on the RTA:

[rta] ACL number 2000

[rta-acl-basic-2000] rule 0 permit source 10.0.0.0 0.0.0.255

[rta-acl-basic-2000] nat address-group 1 200.76.28.11 200.76.28.11

[rta] interface Ethernet0/1

[rta-ethernet0/1] nat outbound 2000 address-group 1

After configuration, both Client_A and Client_B are accessing the Server. The RTA's NAT table might then be ().



37. If a data packet matches multiple routing entries in the routing table of an MSR router, then the correct description of the preferred route order is ( ).
38. The routing table on an MSR router looks like this:

destination/mask proto pre cost nexthop interface

6.6.6.0/24 static 60 1 100.1.1.1 ge0/0

8.8.8.8/32 direct 0 0 127.0.0.1 inloop0

20.1.1.0/24 static 60 100.1.1.1ge0/0

30.0.0.0/8rip 100 100.1.1.1ge0/0

Which of the following analyses of this routing table is correct?
39. Two unconfigured MSR routers are connected as shown in the diagram. After configuring IP addresses, the GE0/0 interfaces of the two routers can communicate with each other.





Now, add the following configuration to both routers:

RTA configuration:

[rta] ospf

[rta-ospf-1] area 0

[rta-ospf-1-area-0.0.0.0] network 192.168.1.1 0.0.0.3

[rta-GigabitEthernet0/0] ospf dr-priority 2

RTB Configuration:

[rtb] ospf

[rtb-ospf-1] area 0

[rtb-ospf-1-area-0.0.0.0] network 192.168.1.1 0.0.0.3

[rtb-GigabitEthernet0/0] ospf dr-priority 0

After the OSPF neighbor states stabilize, which of the following is correct?
40. If all-zero and all-one subnets can be used as valid subnets, the number of valid subnets that can be created from the Class C address 192.168.1.0 using a 26-bit subnet mask is ().

 

GB0-382-ENU Exam Dumps (V8.02) - Secure Your H3C Certified Senior Engineer for Routing & Switching Plus (H3CSE-RS+) Certification with DumpsBase
Tags:,

Related Posts

About The Author

dumps

From our dumpsbase platform you could search what exams you need then test or practice online by yourself. Download the PDF file if you need directly. Any other questions you can mail [email protected]