Choosing Updated NS0-184 Dumps (V11.03) – A Great Way to Pass NetApp NCSIE ONTAP Exam

1. Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.

Which two actions would enable the customer to accomplish this task? (Choose two.)

2. You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.

In this scenario, which feature should you enable?

3. Click the Exhibit button.

You are installing a new AFF All SAN Array A700 HA pair.

Referring to the exhibit, which IP address would have been used to join node 02 to the cluster during setup?

4. You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.

In this scenario, how would you add the shelf?

5. You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.

Which action must be taken to solve the problem?

6. A customer is asked to install a new AFF ASA A700 system. During the installation, the customer asks if ONTAP 9.8 is supported with their host’s OS version running Windows 2016.

In this scenario, which NetApp tool would verify supportability?

7. Click the Exhibit button.

Which set of components on a FAS9000 are highlighted in the exhibit?

8. You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.

Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

9. You want to enable secure communication with the SP or BMC through CA-signed certificates.

Which two certificate types must be installed in this scenario? (Choose two.)

10. After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.

What is required to complete this task?

11. Which logical interface has a fixed firewall policy?

12. Click the Exhibit button.

What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

13. You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither “un-failing” nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.

In this scenario, which two actions should you take? (Choose two.)

14. An administrator issued the cluster setup command and configured a 2-node ONTAP 9.8 cluster.

In this scenario, which tool would the administrator use to validate the configuration?

15. You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.

Which two additional steps must be taken to bring the additional ports online? (Choose two.)

16. You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.

In this scenario, which two flow control settings would you verify? (Choose two.)

17. You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes.

In this scenario, which two resources will help you find a solution? (Choose two.)

18. You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.

In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

19. You are expanding an existing 4-node ONTAP 9.8 cluster with a FAS8300 HA pair by adding a new FAS500f HA pair. Before the expansion, you are asked to save the configuration of the cluster to a backup file.

In this scenario, which two ONTAP configuration backup methods are available? (Choose two.)

20. You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.

In this scenario, which two statements are true? (Choose two.)

21. Click the Exhibit button.

You want to add an AFF A400 system to an existing 4-node cluster.

Referring to the exhibit, which number points to the ports that are used to cable the new nodes to the cluster interconnect switches.

22. Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

23. Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.

In this scenario, what would you tell the customer?

24. Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.

Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

25. You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster that uses NetApp CN1610 cluster interconnect switches.

In this scenario, what are two valid actions for this installation? (Choose two.)

26. You completed a 2-node AFF A700 installation according to the poster. You run the disk show -fields owner command and notice that all drives are assigned to node 1.

In this scenario, which tool would you use to access documentation and guidelines to solve the issue?

27. You have a new 2-node FAS8700 ONTAP 9.8 cluster. One of the nodes has 24x16 TB NL-SAS disks assigned and available for a new aggregate. You created the aggregate with one RAID group and two spare disks.

In this scenario, how many data drives are in the aggregate?

28. Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

29. After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation.

In this scenario, in which three document formats would you create an inventory report? (Choose three.)

30. Which command would be used to measure the throughput and latency of traffic between nodes?

31. You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by “automatic port placement”.

In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

32. Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.

Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

33. You are preparing to physically install a new AFF A400 cluster into a customer’s racks. All equipment has been delivered to the customer’s site.

Which three tools do you need to complete this installation? (Choose three.)

34. Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.

In this scenario, which two prerequisites should you examine in advance? (Choose two.)

35. Click the Exhibit button.

Referring to the numbers shown in the exhibit, which port on an AFF A220 controller is used as port e0M in ONTAP?

36. When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?

37. On which type of network interfaces are the cluster interconnect LIFs created?

38. You are preparing for the installation of a new ONTAP 9.8 cluster and need to get the preinstallation information from the customer.

In this scenario, which NetApp tool would you use to create a configuration spreadsheet template for the deployment?

39. You installed two separate clusters in an isolated data center without outbound network access. The customer wants to troubleshoot issues locally and also create custom Excel reports for capacity utilization from a local server.

In this scenario, which NetApp tool would satisfy this requirement?

40. You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.

In this scenario, what are three examples of data required from the customer? (Choose three.)

41. After the successful installation of a NetApp ONTAP cluster, the customer wants to know how to view telemetry data. The customer also wants to receive online information about any risks with the cluster and potential best-practice gaps.

Which tool satisfies the customer’s requirements?

42. You are setting up a peer relationship between two ONTAP clusters.

In this scenario, which two statements are true regarding authentication?

43. You want to use the NetAppDocs tool to collect information on a newly configured ONTAP 9.8 cluster and to generate a Word document with the details of the cluster configuration.

Which two data sources would you use to collect the necessary data? (Choose two.)

44. Click the Exhibit button.

You are attempting to add a new ONTAP 9.7 node to your ONTAP 9.8 NetApp cluster.

After attempting to add the node, it fails as shown in the exhibit.

What are two nondisruptive ways to add the new node to your ONTAP cluster? (Choose two.)

45. You want to add an AFF A400 HA pair to an existing cluster.

In this scenario, which LIF type is required?

46. You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.

In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)

47. You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.

In this scenario, which front-end FAS8300 network port would you create the data LIFs?

48. Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.

In this scenario, which two methods would be supported to migrate the data? (Choose two.)

49. A customer wants to enable SnapMirror Synchronous across their environment. The customer must ensure that SnapMirror Synchronous will work across the environment.

In this scenario, which two statements are true? (Choose two.)

50. Click the Exhibit button.

After installation of a new ONTAP cluster, you experience a problem. You successfully create a support case on the NetApp Support site. The customer asks you how to view the status of the case.

Referring to the exhibit, which two steps would allow the customer to accomplish this task? (Choose two.)

51. You are using Broadcom BES-53248 switches for a cluster interconnect in a base configuration.

In this scenario, what is the minimum number of ISLs supported between the switches?

52. Which two switch operating system are supported on ONTAP cluster switches? (Choose two.)

53. You are deploying a new AFF All SAN Array A250 into a customer’s existing data fabric.

In this scenario, which two tools would give insight into their existing Cisco MDS fabric configuration? (Choose two.)

54. A customer is creating a new SVM to host iSCSI LUNs for a Hyper-V cluster. You need to successfully map the new LUNs and make them visible to the Hyper-V cluster.

In this scenario, which host information is required to accomplish this task?

55. A customer requires encryption at rest on every node root volume.

In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

56. After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.

In this scenario, which two commands would you use to accomplish this task? (Choose two.)

57. Click the Exhibit button.

Immediately after installing a 4-node FAS8200 cluster, you discover that node, “cluster1-02”, must be removed from the cluster. You want to use the cluster remove-node command to remove the node.

Referring to the exhibit, which two statements are correct? (Choose two.)

58. After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues.

In this scenario, which NetApp tool would have identified these errors after the installation process?

59. Your customer wants to know more about the network configuration within the cluster.

In this scenario, which statement is correct about a LIF?

60. Data ONTAP 9 supports which three features? (Choose three.)

61. You want to create a data volume on aggr0 and you receive a message with the following warning: ''Warning: You are about to create a volume on a root aggregate.

This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?''

What is the reason for this severe performance or stability problem?

62. You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches. In this scenario.

Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)

63. You configured AutoSupport and are trying to send a full AutoSupport message to NetApp. You use the autosupport history show command and see the output shown in the exhibit. The customer confirms that the AutoSupport settings are correct.

Which two actions will solve this issue? (Choose two.)

64. Upon finishing the Installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.)

65. After you install an AFF A700 2-node cluster with DS224C shelves, Config Advisor reports that your SAS cabling is in mixed-path HA. You expected the SAS cabling be in quad-path HA.

You physically verify the LED status on the controllers and the shelves and notice no irregularities. However, a reboot of the SAS expander does not change the output.

In this scenario, what should you do next?

66. Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.

In this scenario, which two statements are correct? (Choose two.)

67. You are asked to install six shelves to a production cluster. The cluster is running clustered Data ONTAP and is a 4-node cluster. All six shelves will be cabled to the same HA pair. The customer wants you to assign all the new disks to a single node in the cluster.

Which three tools would help you accomplish this task? (Choose three.)

68. You were dispatched to install a cluster made up of FAS8060 and FAS8080 controllers. There are three FAS8060 controllers and three FAS8080 controllers.

Which solution would provide the largest possible cluster?

69. What is the minimum number of disks required in a SAS shelf?

70. A host cannot connect to the namespace configured on an NVMe-enabled SVM.

In this scenario, what are two reasons for this problem? (Choose two.)

71. After completing an installation, the customer wants to know how they can manually open a new technical case with NetApp Global Support.

What are three ways to accomplish this task? (Choose three.)

72. You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.

In this scenario, what caused this problem?

73. Which switch vendor is supported for the cluster network switches?

74. You want to add two new nodes to an existing 4-node cluster.

In this situation, what must be considered regarding the cluster interconnect?

75. An iSCSI LIF fails to migrate during a storage failover test. In this scenario, why did the LIF not migrate?

76. Click the Exhibit button.

You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does not want ACP cabled on their cluster.

Which two actions would allow the installation to be completed successfully? (Choose two.)

77. A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.

Which port names are correct in this scenario?

78. When you start a new Service Event Report, what must be entered first?

79. What is the main function of ACP?

80. You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.

What must you consider before you add the addiHonal nodes to clusterA?

81. Exhibit:

While you are introducing the customer to the NetApp Support website, they ask you to ensure that the new ONTAP storage array is covered by support before you complete the knowledge transfer procedure.

Referring to the exhibit, which two widgets would you select to accomplish this task? (Choose two.)

82. What are three reasons to implement FabricPool? (Choose three.)

83. You create a new CIFS data LIF with the default failover group. In this scenario, where will the new LIF failover if the node that owns the new LIF panics?

84. You are ready to purchase a new FAS8200 six node cluster. In this scenario, which three switches are supported as NetApp cluster interconnect switches.

85. A customer has a 2-node FAS8200 cluster with four DS212C shelves with 10 TB SATA drives.

Referring to the exhibit, an aggregate will be created with which default RAID type?

86. You are adding new nodes to a 2-node switchless cluster.

According to NetApp, what must you do before adding the nodes?

87. You have set up a new 2-node switchless cluster and want to verify that the failover is configured correctly.

In this scenario, which two commands accomplish this task? (Choose two.)

88. While troubleshooting an issue with a newly installed system, you used the system controller environment show command.

In this scenario, which issue would be diagnosed with this command?

89. According to NetApp documentation, what should be used when using the Cluster Switch Health Monitor (CSHM) and log collection features?

90. A customer wants to graphically manage a new clustered Data ONTAP system.

Which tool should the customer use?

91. A customer is installing a new system. The administrator needs to have the maximum available amount of data space.

Which disk configuration should the administrator use?

92. Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it.

In this scenario, how would you access Node 4’s management interface?

93. You are setting up a LIF for the node management network.

What will be the default failover policy in this scenario?

94. What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster? (Choose two.)

95. What is the purpose of a mailbox disk?

96. You are assigned to install two DS2246 shelves, three DS4243 shelves, and one DS4486 shelf.

How many rack units (U space) should you account for in this rack layout?

97. Which license is required to enable storage failover?

98. Poppy Pet Care Kennels offers short-term accommodation for dogs whilst their owners are on holiday. The managing director of the company has initiated a project to create a new website that will allow owners to view kennel availability, book kennel accommodation and allow them to monitor their dogs whilst they are away, via a webcam.

The system will also allow kennel assistants to plan the dogs’ feeding times and schedule kennel maintenance.

Customers will be able to leave feedback on the website, which will be reviewed by the quality manager who may respond to comments made by the customer.

The following are potential actors:

A) Poppy Pet Care Kennels

B) Kennel assistants

C) The managing director

D) Customers

E) Quality manager

Which of these would be drawn as actors on the use case diagram?

99. What is a valid failover policy for a SAN LIF?

100. Exhibit:

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.

Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)