CCNP Enterprise ENARSI 300-410 Dumps Updated to V30.02: Check 300-410 Free Dumps (Part 1, Q1-Q40) First

1. Which two methods use IPsec to provide secure connectivity from the branch office to the headquarters office? (Choose two.)

2. Refer to the exhibit.

Why is user authentication being rejected?

3. Refer to the exhibit.

The network administrator configured VRF lite for customer A. The technician at the remote site misconfigured VRF on the router.

Which configuration will resolve connectivity for both sites of customer_a?

4. Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?

5. What is a function of IPv6 ND inspection?

6. An engineer is trying to copy an IOS file from one router to another router by using TFTP.

Which two actions are needed to allow the file to copy? (Choose two.)

7. Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1.

What action will fix the issue?

8. Refer to the exhibit.

Which routes from OSPF process 5 are redistributed into EIGRP?

9. Refer to the exhibit.

Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?

A)

B)

C)

D)

10. Which security feature can protect DMVPN tunnels?

11. Which command displays the IP routing table information that is associated with VRF-Lite?

12. What is a role of route distinguishers in an MPLS network?

13. What is the output of the following command:

show ip vrf

14. Refer to the exhibit.

What is the result of applying this configuration?

15. Refer to the exhibit.

ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console.

Which command is missing from the IP SLA configuration?

16. Refer to the exhibit.

AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server.

Which action resolves this issue?

17. R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

18. DRAG DROP

Drag and drop the DHCP messages from the left onto the correct uses on the right.

19. Which is statement about IPv6 inspection is true?

20. Refer to the exhibit.

What does the imp-null tag represent in the MPLS VPN cloud?

21. Refer to the exhibit.

During troubleshooting it was discovered that the device is not reachable using a secure web browser.

What is needed to fix the problem?

22. Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690.

What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

23. Refer to the exhibit.

A junior engineer updated a branch router configuration. Immediately after the change, the engineer receives calls from the help desk that branch personnel cannot reach any network destinations.

Which configuration restores service and continues to block 10.1.1.100/32?

24. Which transport layer protocol is used to form LDP sessions?

25. Refer to the exhibit.

An IT staff member comes into the office during normal office hours and cannot access devices through SSH.

Which action should be taken to resolve this issue?

26. During the maintenance window an administrator accidentally deleted the Telnet-related configuration that permits a Telnet connection from the inside network (Eth0/0) to the outside of the networking between Friday C Sunday night hours only.

Which configuration resolves the issue?

27. DRAG DROP

Refer to the exhibit.

Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and scheduling Sed

28. Refer to the exhibit.

An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired.

Which command fixes the issue?

29. Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

30. DRAG DROP

Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

31. Refer to the exhibit.

A network engineer for AS64512 must remove the inbound and outbound traffic from link A during maintenance without closing the BGP session so that there ............ a backup link over link A toward the ASN.

Which BGP configuration on R1 accomplishes this goal?

A)

B)

C)

D)

32. Refer to the exhibit.

An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table.

Why is the summary route missing?

33. Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?

34. What does IPv6 Source Guard utilize to determine if IPv6 source addresses should be forwarded?

35. Refer to the exhibit.

Network operations cannot read or write any configuration on the device with this configuration from the operations subnet.

Which two configurations fix the issue? (Choose two.)

36. Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+.

Which action produces the desired configuration?

37. After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides.

Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?

A)

B)

C)

D)

38. Refer to the exhibit.

An engineer has configured DMVPN on a spoke router.

What is the WAN IP address of another spoke router within the DMVPN network?

39. Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family

configuration?

40. Refer to the exhibit.

R1 is being monitored using SNMP and monitoring devices are getting only partial information.

What action should be taken to resolve this issue?