D-PDD-DY-23 Dumps (V12.03) Are the Latest Study Materials for Learning: Continue to Check the D-PDD-DY-23 Free Dumps (Part 2, Q41-Q80) Online

1. A backup administrator is tasked with verifying the compression savings of a PowerProtect DD9900.

Which compression algorithm will they see enabled by default?

2. After adding expansion shelves, an administrator verifies the state of the new disks with the command disk show state is unknown.

Which command will make these disks available?

3. Which command allows a system administrator to monitor clients active in the past 15 minutes?

4. Which deduplication steps are offloaded when DSP is used?

5. An administrator notices that several disks on a shelf show as unknown.

What should be done to resolve this issue?

6. When selecting a PowerProtect DD model, which standard practices should be used to conservatively calculate capacity and throughput?

7. A backup administrator is tasked with monitoring PowerProtect DD capacity metrics. The administrator is backing up 2 TB of data daily with a reduction rate at 5x. After data reduction, subsequent full backups compress down to 100 GB.

The initial backup requires 400 GB with a 10 percent increase in the data each day. Each incremental backup is 200 GB. After data reduction, each incremental backup is 20 GB.

What is the weekly burn rate (GB) after four daily incremental backups and one weekly backup?

8. An administrator is scaling Cloud Tier for a DD9900 by adding a second cloud unit.

What is the required amount of metadata storage (TB)?

9. A PowerProtect DD appliance has been installed at a company’s location for several months and has reached a steady state.

As a best practice, at what percentage of disk utilization should action be taken?

10. A technician is upgrading a DD9400 with a DS60 expansion shelf with 60 drives. In the GUI interface, only 30 drives are accessible.

What is causing these drives to be inaccessible?

11. A PowerProtect DD appliance with two expansion shelves is being installed in a customer-provided rack.

When cabling the controller to the shelves, what is connected to the host port on the last shelf in the chain?

12. Which command is used to start the initial CLI configuration wizard?

13. What is the order of steps to configure DD Boost on a PowerProtect DD appliance?

14. What is a requirement to use the PowerProtect DD HA feature?

15. A customer needs help deploying a shared PowerProtect DD. They ask for best practices when configuring SMT.

What network-related attributes must they configure to increase the security of each tenant unit?

16. What is the maximum backup speed of PowerProtect DD Virtual Edition using Boost?

17. What capabilities are enabled with Retention Lock Governance?

18. What are the terminal emulation settings that are used to establish serial communication with a PowerProtect DD system?

19. When accessing an NFS share from a PowerProtect DD appliance, what is the maximum Mount Limit value for restore instances recommended by IBM Spectrum Protect?

20. Which is required to store and manage archive data on a single PowerProtect DD appliance to comply with regulatory standards?

21. What is the default listen port used by PowerProtect DD systems for replication?

22. Which component of PowerProtect DD is Data Invulnerability Architecture a feature of?

23. A systems administrator wants to change encryption.

Which user role is needed to log in, and what command must be run to enable the security policy?

24. What is a characteristic of Dell Cloud Tier?

25. What is the correct practice when creating Fibre Chanel zones between PowerProtect DD and the media server?

26. Which types of replication are supported in a PowerProtect DD appliance?

27. Which port/protocol is used when using a syslog server to monitor a PowerProtect DD system?

28. An engineer is attempting to add an ES40 shelf to a PowerProtect DD9400. The system currently has one DS60 and four ES40 shelves on the same chain. The system does not recognize the additional shelf.

Why has this occurred?

29. What is the result of using the filesys clean skip schedule estimate-percent-used 30 days 10 command?

30. Which are two attributes of PowerProtect High Availability? ( Select 2 )

31. A storage administrator finished the zoning between the PowerProtect DD and the NetWorker backup server.

How can they verify that the zoning was completed properly and the server HBA are visible?

32. Refer to the exhibit.

Match each action to its call-out location. Select and Place:

33. What are the steps to configure the Retention Lock Compliance?

34. 1.A backup administrator is tasked with verifying the compression savings of a PowerProtect DD3300

Which compression algorithm will they see enabled by default?

35. Which PowerProtect DD feature protects data from accidental or malicious deletion during its retention time?

36. A PowerProtect administrator wants to enable encryption on one of two existing cloud units.

Which statement is true regarding the encryption?

37. For third party backup applications that do not natively support DD Boost where does the DD Boost plug - in need to installed?

38. What is a use case of BoostFS?

39. Which backup application can back up data to a PowerProtect DD system using DD Boost over FC?

40. When using CIFS from a PowerProtect DD system, what should be changed on a Windows machine?