Check 300-410 Free Dumps (Part 3, Q81-Q120) Online to Verify Our 300-410 Dumps (V29.02): Get Valid Materials to Make Preparations

1. What is a function of IPv6 ND inspection?

2. Which statement about route distinguishers in an MPLS network is true?

3. An engineer configured a leak-map command to summarize EIGRP routes and advertise specifically loopback 0 with an IP of 10.1.1.1.255.255.255.252 along with the summary route. After finishing configuration, the customer complained not receiving summary route with specific loopback address.

Which two configurations will fix it? (Choose two.)

4. Which label operations are performed by a label edge router?

5. What is a prerequisite for configuring BFD?

6. Refer to the exhibit.

What is the result of applying this configuration?

7. Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+.

Which action produces the desired configuration?

8. Refer to the exhibits.

Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN.

Which two commands are missing? (Choose two.)

9. Refer to the exhibit.

After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing.

Which two actions resolve the issue? (Choose two.)

10. DRAG DROP

Drag and drop the operations from the left onto the locations where the operations are performed on the right.

11. Which two statements about redistributing EIGRP into OSPF are true? (Choose two)

12. Refer to the exhibit.

ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console.

Which command is missing from the IP SLA configuration?

13. Which protocol is used in a DMVPN network to map physical IP addresses to logical IP addresses?

14. Refer to the exhibit.

The server for the finance department is not reachable consistently on the 200.30.40.0/24 network and after every second month it gets a new IP address.

Which two actions must be taken to resolve this Issue? (Choose two.)

15. Which command displays the IP routing table information that is associated with VRF-Lite?

16. Refer to the exhibit.

AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server.

Which action resolves this issue?

17. Refer to Exhibit.

Which statement about redistribution from BGP into OSPF process 10 is true?

18. Refer to the exhibit.

A user cannot SSH to the router.

What action must be taken to resolve this issue?

19. Refer to the exhibit.

An IT staff member comes into the office during normal office hours and cannot access devices through SSH.

Which action should be taken to resolve this issue?

20. A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap.

Which command allows the logging on the switch to show the time of the flap according to the clock on the device?

21. Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?

22. DRAG DROP

Drag and Drop the IPv6 First-Hop Security features from the left onto the definitions on the right.

23. DRAG DROP

Drag and drop the MPLS terms from the left onto the correct definitions on the right.

24. Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1.

What action will fix the issue?

25. Exhibit:

BGP is flapping after the Copp policy is applied.

What are the two solutions to fix the issue? (Choose two)

26. Refer to the exhibit.

After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1.

Which action can the engineer take to solve the issue so that all the PCs are reachable?

27. While troubleshooting connectivity issues to a router, these details are noticed:

✑ Standard pings to all router interfaces, including loopbacks, are successful.

✑ Data traffic is unaffected.

✑ SNMP connectivity is intermittent.

✑ SSH is either slow or disconnects frequently.

Which command must be configured first to troubleshoot this issue?

28. Refer to the exhibit.

An engineer has configured DMVPN on a spoke router.

What is the WAN IP address of another spoke router within the DMVPN network?

29. What is an advantage of using BFD?

30. Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

31. Refer to the exhibit.

Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?

A)

B)

C)

D)

32. Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

33. What is a limitation of IPv6 RA Guard?

34. What does IPv6 Source Guard utilize to determine if IPv6 source addresses should be forwarded?

35. An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table.

What should be configured to accomplish this task?

36. Refer to the exhibit.

What does the imp-null tag represent in the MPLS VPN cloud?

37. When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”.

What is the reason for the error?

38. Which statement about IPv6 ND inspection is true?

39. During the maintenance window an administrator accidentally deleted the Telnet-related configuration that permits a Telnet connection from the inside network (Eth0/0) to the outside of the networking between Friday C Sunday night hours only.

Which configuration resolves the issue?

40. Refer to the exhibit.

An engineer is monitoring reachability of the configured default routes to ISP1 and ISP2. The default route from ISP1 is preferred if available.

How is this issue resolved?