300-410 Dumps Updated to V27.02 with 594 Practice Exam Questions and Answers – Read 300-410 ENARSI Free Dumps (Part 1, Q1-Q40) Online

1. Refer to the exhibit.

Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet.

Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

2. Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

3. R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

4. Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?

5. Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network.

Which configuration prevents this loop?

A)

B)

C)

D)

6. Refer to the exhibit.

An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen.

What is the reason for this?

7. Refer to the exhibit.

An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table.

Why is the summary route missing?

8. Refer to the exhibit.

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route.

Which action blocks the route?

9. What is a prerequisite for configuring BFD?

10. DRAG DROP

Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

11. Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3.

What is the reason the route is not advertised?

12. Refer to the exhibit.

An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed.

What is the reason for this issue?

13. Refer to the exhibit.

In which circumstance does the BGP neighbor remain in the idle condition?

14. Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

15. Refer to the exhibit.

An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries.

Which action ensures consistency between the two times?

16. Refer to the exhibit.

What is the result of applying this configuration?

17. Which command displays the IP routing table information that is associated with VRF-Lite?

18. Refer to the exhibit.

Which subnet is redistributed from EIGRP to OSPF routing protocols?

19. Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family

configuration?

20. Refer to the exhibit.

Which statement about R1 is true?

21. Refer to the exhibit.

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2.

Which debug command is used to troubleshoot this issue?

22. Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?

23. Refer to the exhibit.

After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1.

Which action can the engineer take to solve the issue so that all the PCs are reachable?

24. Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?

25. Refer to the exhibit.

After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing.

Which two actions resolve the issue? (Choose two.)

26. Which statement about route distinguishers in an MPLS network is true?

27. Which statement about MPLS LDP router ID is true?

28. Refer to the exhibit.

Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?

29. Which list defines the contents of an MPLS label?

30. Refer to the exhibit.

What does the imp-null tag represent in the MPLS VPN cloud?

31. DRAG DROP

Drag and drop the MPLS terms from the left onto the correct definitions on the right.

32. Which transport layer protocol is used to form LDP sessions?

33. DRAG DROP

Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

34. Refer to the exhibits.

Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN.

Which two commands are missing? (Choose two.)

35. Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?

36. Refer to the exhibit.

Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?

A)

B)

C)

D)

37. Refer to the exhibit.

During troubleshooting it was discovered that the device is not reachable using a secure web browser.

What is needed to fix the problem?

38. DRAG DROP

Drag and drop the packet types from the left onto the correct descriptions on the right.

39. DRAG DROP

Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

40. Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+.

Which action produces the desired configuration?