Pure Storage FlashArray Implementation Specialist Dumps (V8.02): Start Your Pure Storage Certified FlashArray Implementation Specialist (FAIS) Exam Preparation

1. An Implementation Engineer is performing a capacity consolidation on an X50R3.

Which command is needed for the engineer to determine whether the customer’s FlashArray supports SAS Flash Modules?

2. On a FlashArray//XR50R2/3 Fibre Channel (FC) array, what is the default type and placement of the PCIe FC card?

3. A data pack has been installed and the puredrive list command shows the drives in “unadmitted” status.

Which command should be used to complete the admission?

4. What is the redundancy of the FlashArray//XL PSUs?

5. Which PCIe slot supports 4-port FC cards on FlashArray//XL?

6. A FlashArray//XR2/3 has an Ethernet mezzanine (EMEZZ), what are the interface names of the ports on the mezzanine?

7. What should an Implementation Engineer do when installing rails in a threaded-hole rack?

8. Support requests a powercycle on a newly-installed FlashArray.

What is the correct way to perform this action?

9. Before leaving the site after an install, who is required to provide completion sign-off?

10. Prior to running the puresetup newarray command, which command should an Installation Engineer run on a new install of an //XR4 array?

11. A customer has a FlashArray X20R3 with 22/22 data packs in the chassis at 80% space usage and wishes to swap one of the data packs for a 45TB pack.

What step needs to be taken to facilitate this consolidation?

12. An Implementation Engineer is onsite to install a new DFM data pack (DP) to CH0.BAY10-CH0.BAY19 of a FlashArray.

After adding the drives to the chassis, which command should the Implementation Engineer run to verify if the new DP is in a wide write group?

13. What is the rack unit height of a FlashArray//XR2/3?

14. An Implementation Engineer is beginning a controller upgrade.

Which command should be run to stop Purity?

15. When transforming an array from SAS to NVMe with the Evergeen XFORM upgrade, when should a swing shelf be installed?

16. The Customer’s Implementation Workbook specifies that the SMTP reply is “outlook.microsoft.com:587”.

What correction should be made for array initialization to be successful?

17. For FlashArray//XL, which 2 PCIe slots should be used for DFS connectivity?

18. After running puredb run giveback --safe command once CT0 has been upgraded, how long should the Implementation Engineer wait before continuing with the controller upgrade?

19. Which command should an Implementation Engineer use to allow Support access to an array?

20. A client needs to upgrade Purity on their FlashArray, but is unable to wait for an available upgrade date from support.

What action should the customer take?

21. If drives need to be relocated within an array for an XFORM upgrade, when should this be completed?

22. A customer would like to consolidate their SAS shelves and wants to evacuate multiple shelves in parallel.

What is a prerequisite for this procedure?

23. After an Implementation Engineer installs a new FlashArray and runs health checks, they see that Phonehome and Remote Assist are NOT working correctly.

Which outbound port needs to be open for all management ports (physical and virtual)?

24. What is the minimum AC voltage required to operate a FlashArray//X20R4 array?

25. What slot does a PCIe SAS card need to be installed in a FlashArray//XR2/3?

26. Which Purity command can be used to validate I/O is balanced across initiators?

27. Before proceeding with a controller upgrade, phonehome logs must be sent.

What command will verify that the logs have been sent?

28. A customer would like to reduce SafeMode settings for retention and eradication with their current policy.

How is authorization obtained to make the requested changes?

29. The customer has completed the installation document and has stated that the proxy server address is “10.24.18.120”.

What additional information is required?

30. A customer has filled out the Installation Workbook. The management IP information netmask is specified as “255.255.255.223” and the gateway is specified as “10.24.18.1”.

What corrective action should be taken to reconcile the IP configuration?