Pass Your ASQ Certified Quality Engineer (CQE) Exam with Confidence Using DumpsBase CQE Dumps (V9.02) – Check CQE Free Dumps (Part 1, Q1-Q40) Online First

1. The primary characteristic of risk management is being

2. Short-run SPC should be used in which of the following situations?

3. Which of the following tools is used to plan for and avoid situations that might interfere with project implementation?

4. Failure to cite the significant contributions of other individuals in a final manuscript for publication violates which category of the ASQ Code of Ethics?

5. The following data sets were presented to top management.

Which problem area should be targeted for improvement first?

6. Which of the following types of planning uses a strategic planning process that relates idealistic goals to work strategy?

7. Which of the following is most important to shaping the culture of an organization?

8. A material review board (MRB) gets its authority to act from which of the following functions?

9. A in this drawing, the symbol is being used to indicate the

10. The producer's risk can be determined from the

11. The number of runs required by a full-factorial design with three factors each at two levels is equal to

12. In a failure mode and effects analysis (FXIEA). the focus should be on

13. Which of the following tools can be used to determine the best option from many choices based on their importance and merits?

14. Which of the following statements is true regarding a failure mode and effect analysis (FMEA)?

15. If a quality engineer discovers a situation in which unlabeled finished product could be shipped to customers, what would be an appropriate preventive action to take?

16. The risk priority number (RPN) is determined by the

17. The relationship between factors can be displayed using which of the following tools?

18. The table below shows the results of inspecting 3,752 items. On the basis of this information, a Pareto chart would show what cumulative percent of nonconformities by the end of the third operation? Calculator

19. Statistical process control was originated by

A. Deming

B. Feigenbaum

C. Jurau

D. Shewhart

20. Which of the following elements describes the combination of the severity and probability of occurrence of harm?

21. Which of the following results is an advantage of a ship-to-stock program?

22. When measurements are taken using a reference scale, such as a pair of calipers, the resulting data are referred to as

23. A company incurred the following quality costs last month.

Incoming material inspection $5,000

What is the total cost of external failures?

24. In reliability testing, operating an item in order to stabilize its characteristics is known as

25. 80° o of weekly inspection non-conforming reports presented to the material review board (MRB) at Marathon Manufacturing Co. end up not being dispositioned for corrective action. Project management developed a risk management plan which included a standard repair manual (SRM) to help mitigate these issues. Only conditions that exceed SRM requirements or specifications will now be forwarded for MRB review. A week after releasing the SRM. the quality engineering team decided to generate and distribute weekly alert reports of non-conformities that exceed SRM requirements or specifications to all inspectors. They also instructed all employees involved in the creation of those discrepancies be re-trained.

Which of the following processes may be considered a risk treatment?

26. Rank in order the following items from most effective to least effective when developing materials for a quality training program.

1. Case studies

2. General examples

3. Job related examples

4. Theory

27. Which of the following tools specifies the use of a feedback cycle?

28. According to ANSI ASQ Z1.4. switching from tightened inspection to normal inspection can occur when how many consecutive lots have been accepted?

29. Temperature measured in degrees centigrade is an example of what type of measurement scale?

30. Typically, a product that exhibits a constant failure rate follows what type of distribution for the failure rate?

31. Which of the following techniques is used when implementing single minute exchange of die?

32. The effectiveness of corrective action can best be assessed by

33. The pre-production or pre-service planning process should include which of the following activities?

34. An auditor who finds a major discrepancy during a pre-award audit of a new supplier should take which of the following actions?

35. The purpose of the opening meeting for an audit is to

36. A company has received many customer complaints due to damaged units being received at the customer's distribution center. After a thorough investigation, it is determined that the units' packaging is insufficient. The company decides that a potential solution is to add reinforcements to the unit packaging to resolve the issue.

Which of the following actions is most appropriate?

37. Refer to the following FMEA table. The columns labeled S. O. and D. refer to ratings of severity, occurrence, and detection, respectively.

Which potential failure mode is most likely to be seen by a customer?

38. If the stated value of a standard is 0.050. and the measurement error is 0.002, which of the following sample data sets shows the greatest precision?

39. Risk control includes making decisions using which of the following pieces of information?

40. A company decides to adopt a total quality system and has started the process by developing quality policies. Rank in order, from first to last, the rest of the steps that need to be performed to implement this system.

1. Audit the system

2. Determine system requirements

3. Develop a measurement system

4. Perform continuous improvement activities H Calculator