Pass Fortinet NSE 5 – FortiSwitch 7.6 Administrator Exam with the Latest NSE5_FSW_AD-7.6 Dumps (V8.02) Today – Achieve Success for 2026

1. Exhibit.

LAG and MCLAG are used to increase the available network bandwidth and enable redundancy.

How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)

2. Which statement about the IGMP snooping querier when enabled on a VLAN is true?

3. What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?

4. Refer to the exhibit.

The FortiSwitch CLI output of the diagnose switch-controller switch-info poe summary command for the switch Access-1 is shown. It shows that two ports have Power over Ethernet (PoE) enabled and are already in use.

What is the most important consideration if you want to connect additional PoE devices to FortiSwitch? (Choose one answer)

5. An administrator must deploy managed FortiSwitch devices in a remote location where multiple VLANs must be used to segment devices. No layer 3 switch or router is present at the site, and the only WAN connectivity is an ISP-provided router connected to the public internet.

Which two components are required to enable VLAN segmentation across this remote site? (Choose two answers)

6. Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

7. Refer to the exhibit.

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

8. Refer to the exhibits.

You enable Dynamic Host Configuration Protocol (DHCP) snooping on the VLAN, Student. The Linux-Client VM sends DHCP requests, and tcpdump confirms the broadcasts. However, the Linux-Server VM, acting as a DHCP server, receives no DHCP traffic.

What is the most likely cause of this intra-VLAN traffic being blocked? (Choose one answer)

9. You are deploying a new FortiSwitch device in a branch office and you want it to be automatically detected and managed by FortiGate.

Which FortiSwitch feature enables automatic detection during deployment? (Choose one answer)

10. Refer to the exhibit.

The security port policy is configured as shown in the exhibit.

Which behavior occurs if a device connected to the port that does not support 802.1X? (Choose one answer)

11. You are deploying a FortiSwitch virtual stack in a network that contains Cisco devices. You want the Cisco devices toautomatically discover the FortiSwitch devices and exchange device information.

Which two protocols must be enabled on the FortiSwitch devices to achieve this? (Choose two answers)

12. Which statement about the quarantine VLAN on FortiSwitch is true?

13. You are configuring VLANs on a FortiSwitch device managed by FortiGate.

Which two statements accurately describe VLAN assignment requirements and behavior on FortiSwitch ports? (Choose two answers)

14. Refer to the configuration:

Which two conditions does FortiSwitch need to meet to successfully configure the options shown in the exhibit above? (Choose two.)

15. Refer to the exhibit.

The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports, and these ports are connected to endpoints which are powered by PoE.

Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?

16. Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

17. Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?

18. 1.Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

19. When Dynamic Host Configuration Protocol (DHCP) snooping is enabled on a FortiSwitch VLAN, which two statements are true? (Choose two answers)

20. How does FortiSwitch determine the route for traffic traversing its interfaces? (Choose one answer)

21. You are designing a FortiSwitch backbone where every FortiSwitch device must connect to every other FortiSwitch for maximum redundancy.

To maintain connectivity while preventing loops, which protocol or feature must you configure on the switches? (Choose one answer)

22. Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces?

23. Which QoS mechanism maps packets with specific CoS or DSCP markings to an egress queue?

24. On supported FortiSwitch models, which access control list (ACL) stage is recommended for applying actions before the switch performs any layer 2 or layer 3 processing? (Choose one answer)

25. Which two requirements must be met before FortiGate can manage a FortiSwitch stack? (Choose two answers)

26. Refer to the exhibits.

An administrator has deployed two FortiSwitch devices, Core-1 and Core-2, as multichassis link aggregation group (MCLAG) peers. These switches are connected to FortiGate for FortiLink and to an access switch (Access-1) using an inter-switch link (ISL). After configuration, the administrator notices that both Core-1 and Core-2 are claiming to be the root bridge in the Multiple Spanning Tree Protocol (MSTP) topology.

What explains this behavior? (Choose one answer)

27. Refer to the exhibits

Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.

Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)

28. Refer to the exhibits.

Port1 and port2 are the only ports configured with the same native VLAN 10.

What are two reasons that can trigger port1 to shut down? (Choose two.)

29. Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?

30. Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)

31. Refer to the exhibits.

An IP phone is connected to port1 of FortiSwitch Access-1. The IP phone tags its traffic with VLAN ID 20. On FortiGate, VLAN IP_Phone (VLAN ID 20) has been configured, and port1 of Access-1 is set with VLAN 20 as the native VLAN. However, the IP phone cannot reach the network. The exhibit shows the partial VLAN configuration and the port1 configuration on Access-1.

Which configuration change must you make on FortiSwitch to allow ingress and egress traffic for the IP phone? (Choose one answer)

32. Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port?

33. Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

34. Which two are valid traffic processing actions that a FortiSwitch access control list (ACL) can apply to matching traffic? (Choose two answers)

35. Which two statements about 802.1X authentication on FortiSwitch ports are true? (Choose two.)

36. A FortiGate is connected to a pair of FortiSwitch devices.

For redundancy, FortiGate must use uplinks on both switches simultaneously without depending on Spanning Tree Protocol (STP).

Which configuration is required? (Choose one answer)

37. Refer to the exhibit.

The command diagnose switch physical-ports summary is executed on FortiSwitch.

Based on the VLAN assignments shown in the output, what is the most likely management configuration of this FortiSwitch? (Choose one answer)

38. Refer to the exhibit.

PC1 connected to port1 has joined multicast group 225.1.2.3 on VLAN 10 with IGMP snooping enabled.

What will happen if you disable IGMP snooping on FortiSwitch? (Choose one answer)

39. Refer to the exhibit.

You have just authorized a new FortiSwitch on your FortiGate, and it appears online in the GUI.

To verify that FortiLink connectivity is healthy, what should you check next? (Choose one answer)

40. Which two statements about managing a FortiSwitch stack on FortiGate are true? (Choose two.)