HPE Master ASE Exam HPE0-J58 Dumps Updated For Your Good Preparation [2022]

1. A customer has a two-node HPE 3PAR array with three additional drive enclosures. There is a single CPG setup for RAID 5 (3+1). One of the drive enclosures has failed and must be replaced.

What needs to be considered before starling the repair?

2. A customer has a Tier 1 application that has high bandwidth and is sensitive to latency.

The customer needs a solution to support this application. The solution must support replication between two sites over dark fiber links and support an RPO of zero.

Which solution meets the customer requirements?

3. You are starting an assessment to design a new multi-storage environment for a customer.

You have collected data on all the current arrays using SAF collector.

What should be the next step in your design process?

4. You are developing reports for a new proposal. You try to use SAF Analyze to upload the customer data you collected, but you receive an error.

What must you do first to begin the process?

5. A startup company is considering an HPE Nimble solution. They have a small IT budget, and they need to be future-proof for changing performance requirements.

How does the Nimble architecture meet the company needs? (Select two.)

6. A customer needs to analyze performance and capacity of their storage environment. Their environment

consists of HPE 3PAR, EMC VNX, and Pure Systems.

Which tool should you use to begin your assessment of their environment?

7. A customer needs to replicate multiple HPE 3PAR source arrays to a single HPE 3PAR target array at a Disaster Recovery sue.

What is required to support a 31 fan-in for Remote Copy?

8. An HPE Nimble customer needs to consolidate storage and scale performance. They are looking to purchase additional hardware to meet these requirements.

What is the best solution to offer this customer?

9. A customer wants to replace an EMC storage array. You want to provide as much Information about the EMC configuration as possible to propose an HPE 3PAR or HPE Nimble Storage array.

Which HPE tool will meet your needs?

10. You want to use FCAP authentication in an environment with FOS 7.3 running switches with no extra licenses.

What should you do to use this feature?

11. A customer requests a proposal for two HPE 3PAR arrays using asynchronous periodic replication. The customer has two data centers, and the current bandwidth available for replication between the data centers is 200 Mb/s.

The customer is replicating 30TB, and the change rate is 3% in 24 hours. The customer wants to achieve an RPO of 10 minutes.

Which statement about bandwidth and replication is true for the customer requirements?

12. A customer needs to upgrade their existing HPE 3PAR environment. They ask you to present a solution to gather data from all 200 of their HPE 3PARs arrays, which are spread across the globe. The arrays consist of various generations and OS levels, and they are managed by regional instances of SSMC.

What should you present to the customer as a solution?

13. A customer needs to replace their outdated storage arrays.

Which resource provides the necessary information to properly size a solution?

14. DRAG DROP

A customer has a primary site with an HPE Nimble Storage array and a secondary site with another HPE Nimble Storage array. The customer had a planned power outage at their primary site, and now needs to switch back to the primary array.

Place the steps into the order they must be performed to switch back the primary array.

15. For customers, what are the benefits of developing a company compliance policy? (Select two.)

16. You are proposing a replication solution to a customer. A competitor offers a solution based on storage

virtualization appliances.

What should you stress about an HPE 3PAR replication solution in regard to the competitor’s proposal?

17. A customer with an existing StoreOnce 5100 appliance needs guidance on determining long-term expected growth of the storage utilization based on actual usage.

However, the customer’s ISV backup software only shows 30 days of historical data.

Which step should be performed to check the StoreOnce 5100 for best practices and allow for growth planning?

18. A customer needs a new replication solution that makes use of capacity efficiency technologies, even though data is being replicated to another array.

You have been developing a solution that includes two HPE 3PAR arrays.

What should you emphasize in your proposal?

19. A customer needs to a multi-site environment where the entire inter-site transmission will be encrypted.

Which

products support this feature without additional licenses? (Select two.)

20. Refer to the exhibit.

A customer requests a solution for two 3PAR 8450 storage arrays using synchronous replication. The customer wants the array configured to…

A junior architect you are coaching created the configuration shown for each array

What should you add to me configuration for each array to meet customer performance requirements?

21. A customer experienced data loss due to a cybersecurity attack. The data could not be restored because the snapshots and backups of the data were also affected.

The customer currently uses HPE 3PAR and RMC as a backup strategy You propose HPE StoreOnce Cloud Bank as an additional backup target.

How can this help mitigate the risk of future cybersecurity attacks?

22. A customer has a requirement to provide disaster recovery for an application. The application has an RPO of 30 mins, with an RTO of 15 mins.

How can HPE 3PAR Remote Copy help meet the customer’s specified requirements in the most cost effective manner?

23. You are using NinjaStars to develop a proposal to refresh a customer's storage infrastructure.

Which information is needed from the existing environment to properly design a solution? (Select two.)

24. A customer attempts to test HPE 3PAR Peer Persistence automated failover by disconnecting the Quorum Witness (QW) link at the source 3PAR. then disconnecting the Remote Copy <RC) link at the source 3PAR one minute later However, failover does not occur

What should you do differently to test Peer Persistence automated failover?

25. A customer has started to load their HPE 3PAR 8450 with data, but are not sure what data reduction they are achieving. They ask you to run analysis and estimate the deduplication ratio of data currently on a virtual volume (VV).

Which CLI command should you use to understand data reduction ratios?

26. Refer to the exhibit, which reflects the Bill of Materials (BOM) configuration for one datacenter.

A customer needs a new storage solution of two HPE 3PAR 8440 arrays. The customer’s environment consists of eight physical servers in each data center attached to the SAN and one StoreOnce 3540 system with two FC I/O cards. The distance between data centers is less than 75 meters.

What should you add the BOM to meet the customer needs?

27. Refer to the exhibit.

A customer is considering a new HPE 3PAR for the purpose of implementing deduplication and compression. Based on the output returned from the NinjaCrawler tool, what do you know about the customer data?

28. A customer has two devices in separate fabrics that need to communicate on a regular basis. The customer does not want to merge these HPE B-series switch fabrics together due to security reasons.

What type of zoning should you recommend that will not merge the two fabrics, but will allow those devices to communicate?

29. A customer requires an all-flash solution that will scale out, with multiple arrays for replication. The customer also needs the solution to provide more data per terabyte of flash storage than competing solutions.

Which HPE program should you leverage in your solution to help meet the customer’s requirements?

30. What must be considered Alien denning a data compliance strategy?