Dell D-PE-OE-01 Free Dumps (Part 2, Q41-Q80) of V8.02 Are Available to Help You Check the Materials – Choose Valuable Resources to Make Preparations

1. A technician is sent on-site to troubleshoot a server that halts during POST. The iDRAC System Event Log shows the following errors: A bus fatal error was detected on a component at bus 0 device 1 function 1 A bus fatal error was detected on a component at bus 1 device 0 function 0 CPU 1 has an internal error (IERR)

The following system information is provided.

Which system component is the most likely cause?

2. One of the servers in a datacenter is set to use the 1+1 power redundancy option with a hot spare. The server uses 1100W PSUs. An SNMP trap has been sent alerting the technician to a PSU failure.

Since this is the "hot spare" PSU, the technician chooses an available, higher capacity Titanium PSU. After replacing the PSU and connecting the power cable, the PSU indicator/handle flashes green, then turns off.

The technician has taken the following actions:

- Reseated the PSU

- Checked the firmware version

- Checked the cable connections

The PSU continues to flash green then turn off.

What should the technician do?

3. A technician receives a repurposed PowerEdge server. After racking and cabling the server, they attempt to log into the iDRAC but cannot do so. The default login account has been disabled.

What method can be used to enable the default login account?

4. A technician resets the iDRAC but when they attempt to log back in to the iDRAC is offline.

Why is the iDRAC offline?

5. A technician deletes the iDRAC Enterprise license on a R640 server.

Which license type is then enabled?

6. How can a technician know whether IDRAC9 System Lockdown mode is enabled?

7. In which Dell EMC PowerEdge server generation was the BOSS card introduced?

8. A technician is setting up SNMP Trap Alerts on a 14G servers.

After specifying the trap destination address, what should be the next step?

9. A Dell EMC PowerEdge server has been updated with an LCC and iDRAC DUP to the latest firmware when performing a firmware rollback?

10. A technician installs a PCIe Host Bus Adapter in a server, powers on the server, then starts the Lifecycle Controller to update the adapter's firmware. Before starting the firmware update, they examine the Current Hardware Inventory. The Host Bus Adapter is not visible so it cannot be selected for a firmware update.

How should the technician address this issue?

11. What type of screwdriver is required to remove the processor heat sink module?

12. A Dell EMC PowerEdge 13G server is being controlled through a secure port by iDRAC8.

What login connection options are available on server using a secure port?

13. A technician installs eight servers into a fully operational rack with top of rack switch Each server has a quad 1Gb NIC and redundant power supplies. The company uses iDRAC in shared LOM mode with LOM1 as the selected NIC.

What should the technician do to verify iDRAC connectivity on each server?

14. Starting from which Dell EMC PowerEdge server hardware generation is the Micro SD card in the IDSDM/vFlash module supported?

15. A technician is tasked to perform a RAID Level Migration (RLM) of a RAID 5 array to a RAID 6 array. They back up data and look in iDRAC Storage and find that the current RAID 5 array is sliced into two virtual disks.

What should the technician do to achieve the desired RAID level?

16. What is a systems management console solution optimized for monitoring and managing Dell enterprise and remote office hardware?

17. Which Dell PowerEdge 16G server has the highest GPU density to run workloads like HPC, AI, DB Analytics, and VDI?

18. A technician builds a bootable ISO with Repository Manager, and then mounts the ISO via the iDRAC virtual console. After the updates have completed, the technician reboots the server to apply the updates. When reviewing the updates, the technician determines NOT all updates were applied.

What is causing this issue?

19. From PERC8 to PERC9, the maximum number of individual drives upon which a virtual disk can be created changed.

How did this value change?

20. What happens when the Hardware Root of Trust fails to validate the BIOS?

21. A technician wants to configure the iDRAC on a new server using the iDRAC Quick Sync 2 feature.

What is required to use this feature?

22. Which sections are included in the iDRAC Troubleshooting tab?

23. A technician needs to improve overall server performance. All servers run a Dell-supported version of RedHat Linux. Turbo boost has been highly beneficial. CPU performance should be maximized, but not at the expense of power usage.

What is the most efficient way to implement these profile options?

24. A remote technician needs to update the iDRAC with Lifecycle Controller firmware using the iDRAC GUI. They have downloaded the iDRAC firmware to the management station and connected to the iDRAC GUI.

What step is required to complete this task?

25. A technician needs to replace a server component with orange tabs/releases.

Which two steps should the technician take to complete this task? (Choose two.)

26. What is used by the Lifecycle Controller to directly back up the server profile on a 14G Dell EMC PowerEdge server?

27. What image does the iDRAC9 BIOS/UEFI Recovery feature use to flash a corrupt BIOS?

28. What type of fans are installed in servers with NVMe storage and GPU configurations?

29. A technician needs to configure a server to allow the OS to manipulate processor frequencies for higher power efficiency.

Which setting can they enable to achieve this?

30. A technician is installing Windows Server 2016 on a server with RAID 1 and RAID 5 virtual disks.

How should they configure the server and deploy the OS?

31. Which front disk chassis option is available in a Dell EMC PowerEdge R740 server?

32. An engineer needs to install an additional PSU on an existing, single PSU Dell EMC PowerEdge R740. They complete the initial installation and cabling procedures. They connect an AC cable and the power distribution unit produces normal AC output. The engineer checks power management and sees that the new PSU is in the Failed state.

What task should be completed to troubleshoot this issue?

33. Where is the LCD panel located on a Dell PowerEdge 16G server?

34. A system administrator is trying to connect with a mobile device to a Dell PowerEdge 16G server using Quick Sync 2. They failed to make a connection.

What is the reason for the failure?

35. Where is the data stored to allow Easy Restore to successfully complete a system board replacement?

36. What category of error is indicated by HWC8011?

37. What is a custom form factor mezzanine card that contains a complete NIC subsystem?

38. What is the drive characteristic of a BOSS M.2 drive in a Dell EMC PowerEdge server?

39. Refer to the exhibit.

A technician tries to apply a BIOS update through the iDRAC web interface on a server using the Linux Dell Update Package file BIOS_2H4CC_LN_2 0.2.BIN. The error shown occurs.

How should this error be fixed?

40. A company that has very specific firmware requirements has acquired Dell EMC PowerEdge servers Any replaced parts of the type must match the original parts identically. The procedure must be as simple as possible with minimal risk.

What action should a technician take to help accomplish this goal?