Share JN0-650 Free Dumps (Part 3, Q81-Q120) Continually: Check the Free Dumps and Verify the Juniper JN0-650 Dumps (V8.02)

1. What does the mac-radius restrict configuration command do?

2. Which statement is true regarding LLDP advertisements?

3. Which two statements are correct regarding the behavior shown in the exhibit? (Choose two.)

4. Exhibit:

You are running OSPF as your IGP. The interfaces connecting two routers are in the ExStart state. You notice that something is incorrect with the configuration.

Referring to the exhibit, which statement is correct?

5. You are using 802.1X in your access network consisting of EX Series switches. You recently had a failure with your RADIUS server which resulted in authenticating client devices being denied access to the network.

You want to change this behavior so that authenticating clients are directed to a remediation VLAN.

Which RADIUS server failback setting satisfies this requirement?

6. Which two statements are true regarding OSPF LSAs? (Choose two.)

7. Which two statements are true about 802.1Z dynamic filters based on RADUIS attributes? (Choose two.)

8. Which command on a Junos device is used to display the operational status of PIM?

9. You are deploying IP phones in your enterprise networks. When plugged in, the IP phones must automatically negotiate the power requirements for the new connection with the EX Series switches.

In this scenario, which protocol should be used to enable this behavior?

10. Exhibit:

Referring to the exhibit, you must advertise the 100.0.0.0/16 routes from AS1 to AS2, but R2 is not advertising any BGP routes to R5.

Why is this happening in this scenario?

11. You are configuring port ge-0/0/0 on an EX Series switch connected to an IP phone that does not support LLDP-MED.

Which three configuration statements do you need to accomplish this task? (Choose three.)

12. You have configured a multicast enabled network and are using bootstrap to elect an RP. Your network connects to a peering network that is also multicast enabled, and you want to ensure that your Bootstrap information does not leave your domain.

Which two statements are true? (Choose two.)

13. When configuring an Anycast RP, which of the following is true?

14. Exhibit:

The policy shown in the exhibit is applied as an export policy to your BGP neighborship.

Which action will be taken for route 12.233.45.5?

15. Which two statements describe a multicast source tree? (Choose two.)

16. You are configuring MSTP to prevent loops in your layer2 network. After applying the configuration, you notice that MSTO is not working correctly

Referring to the exhibit what is causing the problem?

17. Which statement is true regarding the community regular expression "^((105)|(207)|(309))):((1.{3,4})|([256].*)|(.*[3479]))$"?

18. What is the function of a private VLAN?

19. Referring to the exhibit, what is the significance of the * next to an interface?

20. You are implementing 802.1x authentication in your Layer 2 network. Each user will have a computer and a phone and you must ensure that both device are authenticated individually.

In this scenario, which supplicant mode should be used?

21. A Layer 2 connection does not expend across data centers. The IP subnet in a Layer 2 domain is confined within a single data center.

Which EVPN route type is used to communicate prefixes between the data centers?

22. Referring to the exhibit, which two statements are true? (Choose two.)

23. Exhibit:

Referring to the exhibit, which statement is true?

24. What are two similarities between OSPFv2 and OSPFv3? (Choose two.)

25. You have configured a EX Series access switch to support VoIP phones. The voice VLAN has been configured to manage voice traffic. There is a computer and a VoIP phone connected to the same switch port.

The VoIP phone is sending traffic with a VLAN tag.

Which statement is true?

26. When configuring MDSP with peers in other multicast domains, which two statements are true? (Choose two.)

27. In IS-IS advertising POUs with the overload bit has which effect?

28. What is the role of the Rendezvous Point (RP) in multicast networks using PIM Sparse Mode?

29. Which BGP message type contains NLRI information?

30. How is MSDP used in conjunction with PIM-SM?

31. Referring to the exhibit, which two statements are correct? (Choose two.)

32. Which two statements are true regarding Spanning Tree Protocol? (Choose two.)

33. In Junos, which command can be used to troubleshoot IS-IS protocol issues?

34. Referring to the exhibit

How will router E quickly learn that the remote MAC addresses are no longer reachable through the router attached to the failed link?

35. You have configured 802.1x access control.

Which statement is true when the RADIUS server is unreachable by the switch?

36. In the context of Junos, what is the purpose of the 'multicast' routing-options configuration hierarchy?

37. Which two authentication methods are available for OSPF on Juniper devices? (Choose two.)

38. You are configuring an OSPF network that contains 1G, 10G, and 40G links. You want the metric of each link to be automatically calculated based on the link bandwidth so that higher-speed links are a lower cost than lower-speed links.

Which statement is true?

39. Referring to the outputs shown in the exhibit, which two statements are correct about the IS-IS adjacency? (Choose two.)

40. Which statement is true regarding multifield classification?