HPE6-A89 Dumps (V8.02) Are Available with 100% Success Guaranteed: Pass Your HPE Networking Comware Exam Successfully

1. Which prompt indicates that a user is in the system view of a Comware device?

2. Which Comware feature helps prevent unauthorized brute-force login attempts?

3. Scenario: An enterprise is deploying OSPF in a multi-area design. One department is assigned to Area 10, and another to Area 20. Both connect to a central Area 0. They want to restrict Type 5 LSAs from entering Area 20.

Which area type should you configure for Area 20?

4. Scenario: An engineer upgrades the system image on a Comware switch and wants to ensure the device boots with the new version after a reboot.

Which command should the engineer use to accomplish this?

5. Which of the following statements is true about External BGP (eBGP) neighbors?

6. What happens if no ACL rule matches a packet and there is no default permit statement?

7. What must be configured after assigning a port to a VLAN in access mode?

8. Which of the following is true about PIM Dense Mode (PIM-DM)?

9. Which command tests basic IP connectivity from a Comware switch?

10. Which command in Comware enables a BGP process for a router in AS 65001?

11. Scenario: You want to restrict multicast traffic to only receivers that explicitly request it, and the application supports Source-Specific Multicast (SSM).

Which configuration should you ensure is enabled?

12. Which of the following BGP attributes is mandatory in every route advertisement?

13. 1.Scenario: You are configuring port GigabitEthernet1/0/10 on a Comware switch. The port should belong to VLAN 20 and should not tag traffic.

Which two commands must you use?

14. Scenario: You’re configuring a Comware switch to act as a DHCP client on interface Vlan-interface 100 to receive an IP address automatically from a DHCP server.

Which command must be applied within the VLAN interface configuration?

15. Scenario: A junior network engineer configures a user account on a Comware switch but forgets to assign a privilege level. The engineer reports they cannot execute administrative commands after logging in.

What is the likely cause?

16. Scenario: Your network has two upstream providers using eBGP. You prefer to use the provider connected to Router A for outbound traffic.

What’s the best way to influence outbound path selection in BGP?

17. Which command copies the current configuration to the startup configuration file?

18. Scenario: A network has three interconnected Comware switches. The administrator notices redundant links but wants to prevent loops while still maintaining redundancy.

Which feature should be enabled to achieve this?

19. Scenario: Your customer wants to limit YouTube traffic to 2 Mbps on a specific uplink port but allow all other traffic without restriction.

What configuration approach should be used?

20. Scenario: Two Comware switches are part of an IRF fabric. The master switch fails unexpectedly.

What happens next in the IRF topology?

21. Which mode must an interface be in to carry traffic for multiple VLANs?

22. What is the primary purpose of using multiple OSPF areas?

23. What is the primary goal of implementing QoS on a network switch?

24. Which command saves the current configuration to the startup configuration file in Comware OS?

25. Which command enables DNS lookup on a Comware device?

26. Scenario: You are troubleshooting a network where users are experiencing delays during topology changes. The switches are using default STP settings.

What can be done to reduce convergence time?

27. Which command enables IP routing on a Comware switch?

28. What is the function of the PVID on a trunk port?

29. Which command would you use to apply a QoS policy to an interface?

30. Which type of ACL in Comware matches only on the source IP address?

31. Scenario: You have applied ACL 2001 on interface GigabitEthernet1/0/10 in the outbound direction. Users report blocked traffic even though you permitted their subnet.

What is the most likely cause?

32. Scenario: An administrator is configuring a new HPE Comware switch. After connecting via the console port, they want to enter the system view to begin configuration.

What command should the administrator use?

33. Which command verifies the current IRF topology and role of each switch?

34. What is the default user privilege level when accessing a Comware device via the console port?

35. Scenario: You have enabled multicast routing on your Comware switch and configured PIM-SM on VLAN interfaces. However, clients are not receiving multicast streams.

Which step should you take next?