Choose NS0-164 Dumps (V8.02) for Your NetApp Certified Data Administrator, ONTAP Exam Preparation: Check NS0-164 Free Dumps (Part 1, Q1-Q40) First

1. Which two supported methods would you use to restore data from a SnapVaultfor NetBackup Volume?

2. Identify the two SnapMirror commands that are entered on the destination storage appliance.

3. Which one of the following actions will cause a currently in sync snapmirror relationship to fall out of sync?

4. You cannot disable the SyncMirror license if one or more mirrored volumes exist.

5. You are troubleshooting a clustered failover problem at a customer site. The customer explains that both storage appliances were NFS mounted onto the Solaris host. You attempt to create a file on the NFS mount point for the inaccessible appliance, but you get the following error: NFS server filer2 not responding still trying.Symptoms:

1) When not in takeover mode, both storage appliances operate normally.

2) In takeover mode, the taken over node is not accessible on the network.

You perform a "cf giveback" and you can now create a file over NFS on both appliances.

What should you do first to resolve this issue?

6. For aggregates or traditional volume SyncMirror to work correctly, the configuration of each plex must be identical with regard to____________.

7. Which statement describes the results of the snapmirror resync command?

8. Which three tools present statistics from the Data ONTAP counter manager? (Choose three.)

9. It is the use of the -Lflag in the snapmirror initialize command and the subsequent successful level 0 transfer that causes the destination volume to become snaplocke?

10. Which two default HA features work together to reduce and avoid client outages on an ONTAP FAS cluster? (Choose two.)

11. You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is

12. What is the maximum distance between a standard clustered pair?

13. Which two protocols provide NAS access for home directories on an $VM? (Choose two.)

14. Due to the sensitive nature of AutoSupport messages, what transport protocol should a storage administrator configure?

15. When Data ONTAP creates a weekly, nightly, or hourly snapshot, the value of n (as shown by the UNIX Is command) is adjusted for all the weekly, nightly, or hourly snapshots. The higher the value of n. the_________the snapshot.

16. In a fabric-attached MetroCluster, hardware disk ownership by a node is determined by which two factors (Choose two.)

17. Identify the two commands that could be entered on a system with a SnapMirror source. (Choose two.)

18. If you were troubleshooting and wanted to look at SnapMirror log files, what is the path and directory to these files?

19. A mirrored volume has a failed disk, but there are no available spares in the pool from which the degraded plex was built. Data ONTAP will:

20. You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists.

Which one of the following is the most likely explanation?

21. For a configuration change to be effective when using the OSSV configurator, the OSSV service must be restarted.

22. The required hardware to add SyncMirror to an existing system would be ___________.

23. A volume is SnapMirrored hourly. You revert the volume using a snapshot that was created two days ago.

Which command continues the relationship?

24. To remove a cluster setup, you must perform the following steps.

1. Type cf disable.

2. Unlicense cluster.

3. Remove partner entries for network interfaces from the /etc/rc file.

4. Halt and make sine the partner-sysid is blank.

5. Power down and remove the cluster interconnect card.

6. Perform steps 1-5 above on the partner node.

25. Which tool is available on a non-NetApp primary system to assist in starting or stopping SnapVault, modifying NDMP settings, enabling debugging, and capturing trace files?

26. Which command displays the disk ownership for both CPU modules in a FAS270C appliance?

27. Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?

28. To restore a primary SnapVault qtree to the exact qtree location on the primary storage system (from which it was backed up), you must:

29. The snapvault snap sched-x command can be used to:

30. The NearStore system is not the recommended secondary storage appliance for Open System SnapVault.

31. What console message is a good indication that the storage appliance is ready to reinstate the cluster from a previous takeover?

32. An administrator has an ESXi cluster with VMware VMFS LUNs on an AFF system. Alter troubleshooting performance issues, the administrator determines that timeout best practices are not set on the hosts.

Which NetApp tool would apply the best practice settings?

33. Which two configurations ensure end users are able to restore previous versions of files? (Choose two.)

34. When you are setting up SnapMirror, which one of the following is not a replication pre-requisite?

35. If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank

36. Five minutes ago, you performed a single file SnapRestore on a large NFS file. 40% of your NFS users are now complaining about getting "stale file handles" for the file.

Which one of the following is the most likely cause of this problem, and the best procedure to correct it?

37. Which two tools can be used to actively monitor ONTAP cluster performance? (Choose two.)

38. Which two products can be used to administer Cloud Volumes ONTAP? (Choose two.)

39. Which two conditions would prevent an ONTAP upgrade? (Choose two.)

40. A SnapVault secondary volume can contain up to ______________ Snapshot copies for data protection.