CWDP-305 Dumps Updated to V10.02: Come to Read the CWDP-305 Free Dumps (Part 1, Q1-Q40) Online and Pass Your Exam with Confidence

1. When designing a Wi-Fi-based WLAN to support voice in a large office, which design element is of the highest concern for performance?

2. What is the minimum PoE budget required to power 6 APs using IEEE 802.3at with no additional details provided?

3. In high-density environments like stadiums or convention centers, what additional factor must be considered that can attenuate Wi-Fi signals during events?

4. Which document outlines the objectives, scope, and key stakeholders, serving as the official authorization to begin a WLAN design and deployment project?

5. When conducting information gathering for a WLAN design, which document ensures your customer's proprietary information remains confidential and protected from unauthorized disclosure?

6. In WLAN location-based services, which metric, despite being commonly used, offers the lowest accuracy when determining device positions?

7. Your customer uses PSK authentication but needs a more secure, certificate-based solution requiring certificates on both the client and server.

Which EAP method is the most appropriate?

8. When designing a wireless bridge to connect two offices 13 kilometers (approximately 8 miles) apart, which factor must the Wireless Engineer consider to account for Fresnel Zone clearance?

9. While conducting a site survey in a heavy machinery repair facility, what essential gear should you use for safety in this challenging environment?

10. A North American business traveler connects to a hotel's 2.4 GHz SSID in Europe and notices low RSSI from an AP in the room, but experiences no issues with RSSI in the lobby.

What is the most likely reason for the low RSSI in the room?

11. A museum requires its wireless access points to be discreetly integrated into the environment without sacrificing performance.

Which design choice best meets this requirement while maintaining optimal functionality?

12. An engineering firm upgraded from nine 802.11n APs to nine 802.11ac APs, retaining the same channel and power configuration. Despite this, throughput remains unchanged.

What is the most likely reason for the lack of improvement?

13. During a public Wi-Fi session with 10 other users, you run a ping sweep but cannot detect any devices on your subnet.

What feature is likely enabled on the WLAN infrastructure to prevent local communication between clients?

14. While implementing 802.11ax APs in the 6 GHz band, a consultant recommends using WPA2-Personal for VoIP support.

Why is this approach technically inappropriate?

15. While planning for a VoWLAN deployment requiring 25 dB SNR, you measure the noise floor at -88 dBm.

What is the minimum RSSI needed to meet the system's performance requirements?

16. When deploying an Enterprise-class VoWLAN infrastructure, which Access Category (AC) must be used to prioritize voice packets and ensure optimal performance?

17. When using a WLAN design tool with propagation modeling capabilities, what critical step must be performed before adding APs, antennas, and attenuation factors like walls?

18. Your customer's 802.11n laptops cannot detect the SSID in the 5 GHz band in a conference room, but your 802.11ac laptop connects without issue.

What is the most likely explanation for this discrepancy?

19. When designing a static channel plan for an office using voice devices near an airport, which range of channels may be avoided to avoid channel switching when implemented in this environment?

20. Which vertically polarized antenna is best suited for a WLAN infrastructure with access points mounted on a ceiling over 6 meters high, where all client stations operate from the floor level?

21. When using a predictive design tool, you have selected access points (APs) with an antenna gain of 3 dBi and set the transmit power to 25 mW.

What is the EIRP (Effective Isotropic Radiated Power) of the APs in this design?

22. Your customer has selected switches that support 802.3bz MultiGig interfaces and 4x4:4 802.11ac Wave 2 APs with dual-5GHz capabilities. The APs have one MultiGig interface, and some cable runs will exceed 180.5 feet (55 meters).

To support MultiGig speeds, which is the best cabling option?

23. When conducting a site survey for a possible WLAN redesign, you use two Wi-Fi USB adapters for RSSI data collection and two USB spectrum analysis adapters for RF spectrum data. Since your laptop lacks enough USB ports, you connect them via a 4-port powered USB 3.0 hub.

What issue could the use of USB 3.0 cause that might impact your site survey?

24. What is the most cost-effective way to accurately measure the height of a ceiling when the use of a ladder is not permitted?

25. You conducted a site survey using two USB Wi-Fi adapters with a special driver designed for the site survey software. After deployment, the client devices show lower RSSI values compared to the results from your survey.

What is the most likely reason for this discrepancy?

26. When performing an active site survey in an existing WLAN infrastructure, in addition to gathering throughput data, what other important function are you typically testing simultaneously?

27. Why should band steering algorithms allow stations to connect to the 2.4 GHz band after ignoring a certain number of Probe Requests?

28. After designing a WLAN infrastructure using predictive design software, what is the best way to validate the predictive design in the physical space before deployment, assuming time and budget allow for it?

29. Your customer requires a security solution where client credentials are used, not a Protected Access Credential (PAC), and the authentication server must have a certificate with optional client certificate use.

Which EAP (Extensible Authentication Protocol) method is the best fit for these requirements?

30. Your customer requires fast and secure roaming.

Which two types of roaming are specified in 802.11 Fast Transition (FT) that will help meet this goal?

31. Which advantage provided by 802.11n and 802.11ac is not usable in 1x1:1 low-end client devices?

32. When deploying access points (APs) outdoors, which additional component needs to be used that is typically not required in most indoor office deployments?

33. Which document provided to your customer should include all devices and parts that will be used during the deployment of their WLAN infrastructure?

34. What limitation exists when WMM is not enabled on an 802.11 WLAN?

35. When designing for OFDMA, why might the same channel bandwidth result in greater efficiency than that available in 802.11n and 802.11ac?

36. What service must be implemented on your customer's network to authenticate users against an LDAP database before granting access to the WLAN infrastructure?

37. What is the best method of gathering attenuation measurements from wall materials?

38. Which type of authentication and encryption method is mandatory for Voice Enterprise certified devices as specified by the Wi-Fi Alliance?

39. Which document provides detailed instructions for installation technicians on how to properly mount and configure access points (APs)?

40. In addition to a copy of your design, which tools should you provide to ensure the installation team correctly deploys access points (APs) in the specified locations within a multi-floor indoor design?