FREE to Test E20-593 DELL EMC Exam Questions Online

1. A backup administrator is configuring an EMC NetWorker embedded storage node within an EMC Disk Library (EDL).
To ensure that the embedded storage node is used to write clone data, what is required?

2. What describes the use of Tape Stacking with the embedded storage node on an EMC Disk Library (EDL)?

3. An EMC NetWorker customer wants to clone save sets from an EMC Disk Library (EDL) to a physical tape library. The customer requires full catalog tracking with minimum SAN utilization.
Which solution best satisfies these requirements?

4. A customer has a single-engine EMC Disk Library (EDL) and wants to enable the EMC NetWorker embedded storage node. How is this done?

5. After creating an EMC NetWorker advanced file type device, you notice that the corresponding read-only device is missing. What is a possible cause?

6. Refer to the exhibit.


A storage administrator configures an EMC NetWorker staging policy to move save sets from backup Device A to backup Device B. A restore session is started and requires save sets that were staged to Device B.
What is the data flow in this recovery?

7. What is a characteristic of an EMC NetWorker advanced file type device?

8. What happens when an EMC NetWorker file type device becomes full while backups are running?

9. Your customer needs to back up a Windows file server containing millions of small files to their EMC Disk Library using EMC NetWorker. They have a very limited backup window for this client and need to limit the impact on the server.
What is the best way to fulfill the customer’s requirements?

10. An EMC NetWorker administrator configures an advanced file type device, setting the device target sessions to two, and max sessions to four.
How is data written to the advanced file type device?

11. Your task is to develop a backup-to-disk solution for your client. After an initial analysis, you decide to include one EMC Disk Library (EDL) to be used as the primary backup device. The customer has been using a physical library with LTO-3 drives for many years and would like to have the capability to recover from the old tape. The solution must result in the fewest possible changes to the EMC NetWorker server.
How can you best address these requirements?

12. Client A performs backups to Storage Node S where the backup operations are managed by EMC NetWorker Server N. NetWorker Management Console is running on Server Y. Client A's configuration information was lost.
To which component must the client configuration data be restored?

13. What command was used to see the following NDMP device?
[email protected]:ADIC Scalar i2000 100A|Autochanger (Jukebox), /dev/mc_d6l0
S/N: 02TOK00200
ATNN=ADIC Scalar i2000 02TOK00200
Virtual device
[email protected]:IBM ULTRIUM-TD4 7BG2|Tape, /dev/mt_d0l0
S/N: 1310056061
ATNN=IBM ULTRIUM-TD4 1310056061
WWNN=500104F000A11D3F
WWPN=500104F000A11D40

14. You are deleting save sets manually from the EMC NetWorker server using CLI commands. You receive an error that the database update has failed.
What process should you verify is running on the NetWorker server?

15. What is a characteristic of EMC NetWorker's Open Tape Format (OTF)?

16. What is the primary function of the EMC NetWorker job daemon?

17. A customer is running an EMC NetWorker 7.6 server on a UNIX platform and wants to monitor backup operations from the command line.
Which utility can be used?

18. EMC NetWorker is using a library controlled by an ACSLS server.
Which NetWorker command can be used to discover volumes on the NetWorker server?

19. In an EMC NetWorker storage node with four stand-alone LTO tape drives, which daemons must be running?

20. A customer has the following EMC NetWorker configuration:
• Two remote storage nodes, Node A and Node B
• Two virtual tape libraries configured on Node A and Node B, respectively
• Twelve virtual tape devices with four drives attached to the NetWorker server, Node A and Node B, • respectively
How many nsrlcpd processes are running on the NetWorker server?