Explore the NSE5_SDW_AD-7.6 practice tests at DumpsBase and download the latest exam questions to prepare for your Fortinet NSE 5 – SD-WAN 7.6 Core Administrator exam with confidence. The current version contains 144 questions and answers. Learning these Q&As can help you review SD-WAN administration concepts and find topics that need more study.<\/p>\n\n\n\n
The NSE5_SDW_AD-7.6 Fortinet NSE 5 – SD-WAN 7.6 Core Administrator exam is available to assess your practical knowledge of Fortinet Secure SD-WAN deployment, configuration, administration, and operation. Currently, It covers WAN connectivity, application steering, routing, performance monitoring, FortiGate integration, centralized management, and troubleshooting. All the exam objectives will be tests in three areas:<\/p>\n\n\n\n
Additionally, the Fortinet NSE 5 – SD-WAN Core Administrator is one of the proctored exams in the NSE 5 in Secure Networking certification track:<\/p>\n\n\n\n
This track covers the deployment, management, and monitoring of Fortinet core network security products. Before attending the NSE 5 exam, you must complete the NSE 4 FortiOS certification.<\/p>\n\n\n\n
Among these three exams, the NSE5_SDW_AD-7.6 is available for the network and security professionals who deploy and administer Secure SD-WAN solutions. It is highly recommended to have three years of networking experience, three years of network security experience, and two years with FortiGate and FortiManager.<\/p>\n\n\n\n
Preparing for the Fortinet NSE 5 – SD-WAN 7.6 Core Administrator certification requires a solid understanding of SD-WAN technologies, network management, configuration, and troubleshooting. Candidates need to become familiar with the relevant concepts and understand how to apply them in different network administration scenarios. DumpsBase provides NSE5_SDW_AD-7.6 practice tests designed to support candidates throughout their preparation journey. With NSE5_SDW_AD-7.6 practice questions, learners can review important concepts and check how well they can apply Fortinet SD-WAN knowledge.<\/p>\n\n\n\n
A Best Quality SD-WAN rule uses latency as its quality factor. Both candidates have valid routes and the same measured latency of 220 ms.
The relevant settings are:<\/p>\n\n\n\n
set mode priority\nset priority-members 2 1\nset link-cost-factor latency\nset link-cost-threshold 10\n<\/code><\/pre>\n\n\n\nMember 2 is wan2; member 1 is wan1.
Which interpretation of the configured preference is correct?
A. wan1 receives the preference because it has the lower member ID; the measured latency is unchanged.
B. wan2 receives the preference in the metric comparison; its measured latency is not physically reduced.
C. wan2 receives the preference by reducing its actual measured latency from 220 ms to 200 ms.
D. wan1 receives the preference by reducing its actual measured latency from 220 ms to 200 ms.
Answer:<\/strong> B
Explanation:<\/strong> Member 2 (wan2) is first in priority-members<\/code>, so it receives the configured comparison preference. The documented latency example applies the advantage as latency \/ (1 + threshold). With equal 220 ms measurements and a 10% threshold, wan2 has a comparison value of 220 \/ 1.10 = 200 ms, versus 220 ms for wan1. This affects selection; it does not improve the actual 220 ms latency.<\/p>\n\n\n\nQuestion 2<\/h3>\n\n\n\n
In FortiManager SD-WAN Monitor Table View, a VPN interface is shown as up, but the Link Mode entry has no physical speed or duplex information. A physical interface does display those details. No other fault evidence is supplied.
Which documented limitation explains this difference?
A. Every VPN interface without a speed value has failed its SLA.
B. Speed and duplex are shown only after the VPN is converted to a normalized interface.
C. Speed and duplex information in Link Mode is available only for physical interfaces.
D. Link Mode is a historical-session counter and cannot show any interface status.
Answer:<\/strong> C
Explanation:<\/strong> The Table View Link Mode column displays link status, speed, and duplex, but Fortinet limits speed and duplex information to physical interfaces. A VPN entry lacking those details is consistent with the display’s scope.<\/p>\n\n\n\nQuestion 3<\/h3>\n\n\n\n
An established source-NAT (SNAT) session on FortiOS 7.6.3 uses wan1. The global snat-route-change<\/code> setting is disabled. A routing change makes a route through wan2 preferable, but the original route through wan1 remains active and usable. No other session-clearing or failure event occurs.
What is the documented default behavior for this existing SNAT session after that routing change?
A. It immediately moves to wan2 while retaining its old SNAT selection.
B. It must be deleted because an active session cannot survive a route preference change.
C. It keeps using wan1 while the original route remains active.
D. It immediately moves to wan2 and applies a new SNAT selection.
Answer:<\/strong> C
Explanation:<\/strong> With SNAT enabled, an existing session normally keeps its outbound interface after a routing change as long as its old route remains active. Under the stated conditions, the session keeps using wan1.<\/p>\n\n\n\nQuestion 4<\/h3>\n\n\n\n
An administrator has selected passive mode for an SD-WAN performance SLA. Real TCP application traffic is available, but the matching firewall policy has not yet been prepared for passive WAN health measurement.
Which two policy settings are required to collect passive measurements for that traffic in FortiOS 7.6.3? (Choose two)
A. Enable passive-wan-health-measurement<\/code> on the policy that accepts the traffic.
B. Use an individual SD-WAN member as the policy outgoing interface instead of its zone.
C. Set the policy outgoing interface to the appropriate SD-WAN zone.
D. Keep auto-asic-offload<\/code> enabled on that policy as a prerequisite for passive measurement.
E. Replace passive mode with active mode before the policy can contribute measurements.
Answer:<\/strong> A, C
Explanation:<\/strong> Passive health measurement analyzes real TCP session information. The accepting firewall policy must enable passive-wan-health-measurement<\/code>, and its outgoing interface must be an SD-WAN zone.<\/p>\n\n\n\nQuestion 5<\/h3>\n\n\n\n
An administrator finishes the SD-WAN Setup wizard for a new dual-WAN deployment. The review confirms that the zone, two members, performance SLA, and service rule were created. No default route has been configured separately.
Which follow-up task does the documented wizard workflow require?
A. Add a third member before the two-member configuration becomes usable.
B. Replace the created zone with a physical WAN interface in the service rule.
C. Configure a default static route for the newly created SD-WAN zone.
D. Delete the created SLA so that the wizard can generate a default route.
Answer:<\/strong> C
Explanation:<\/strong> The wizard creates the selected zone, members, performance SLA, and rule, but its documented workflow still requires a default static route for the new SD-WAN zone afterward. Completing the wizard does not establish that the default-route requirement has been satisfied.<\/p>\n\n\n\n