Cisco Industrial Networking Specialist IMINS Exam 200-401 Dumps

Before talk about Cisco 200-401 IMINS exam, you need to know Cisco Industrial Networking Specialist certification first. This certification ensures candidates have the foundational skills to manage and administer networked industrial control systems. Getting Cisco Industrial Networking Specialist certification successfully requires you answer Cisco 200-401 exam. Cisco IMINS 200-401 Managing Industrial Networks with Cisco Networking Technologies exam is a 75 minute, 60 – 70 question assessment. 200-401 dumps are valid to ensure that you can pass Cisco IMINS 200-401 exam successfully.

Free Demo Questions of Cisco Industrial Networking Specialist IMINS Exam 200-401 Dumps, read carefully to find why you need to choose.

1. Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?

 
 
 
 

2. Exhibit:

Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.)

 
 
 
 
 
 

3. Exhibit:

Which two statements are correct for a safe wiring installation to the terminal block of the switch or endpoint? (Choose two.)

 
 
 
 
 
 

4. What are two benefits of a star network topology? (Choose two.)

 
 
 
 
 

5. Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.)

 
 
 
 
 
 

6. What is the purpose of Spanning Tree Protocol?

 
 
 
 
 

7. Exhibit:

Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch?

 
 
 
 

8. Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration?

 
 
 
 

9. Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure?

 
 
 
 

10. Which two ports does EtherNet/IP use to communicate? (Choose two.)

 
 
 
 
 
 

11. EtherNet/IP is an Ethernet implementation of which protocol?

 
 
 
 

12. Which prompt is used to configure parameters for the Ethernet ports of an industrial switch?

 
 
 
 
 

13. What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.)

 
 
 
 
 

14. According to the Purdue Reference Model, at which layer would you perform manufacturing operations and control?

 
 
 
 
 

15. An administrator has connected devices to an industrial switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. What must be done to accomplish this?

 
 
 
 

16. Exhibit:

Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

 
 
 
 

17. Exhibit:

Refer to the exhibit. An industrial ruggedized network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation?

 
 
 
 
 

18. DRAG DROP

19. DRAG DROP

20. Which characteristic causes multimode fiber-optic cable to differ from single mode?

 
 
 
 

 

Updated CCNP Wireless 300-360 WIDESIGN Exam Dumps
Cisco Service Provider Routing Field Engineer 500-230 Exam Dumps

Add a Comment

Your email address will not be published. Required fields are marked *